Cardin Elettronica BLTOW24 Serie Bedienungsanleitung Seite 10

PROGRAMMING PROCEDURE (parameter setting)
• All the functions of the electronic programmer can be set in the Display menu "LCD1" using the three buttons contained therein:
- use the arrows to navigate through the menu and/or to adjust the display contrast;
- use "PROG/OK" to modify the parameter settings and/or to confirm.
PROGRAM
OPTIONS
OPTIONS
TB FI TA TD
SAFETY DEVICES SAFETY DEVICES
FS CP TC TAL
MOTION MOTION
Arrow
DISPLAY DISPLAY
to scroll
REMOTE
00.000.007 REMOTE
CC2X24 V1.00
"PROG/OK"
to confirm
Press an arrow
SEQUENTIAL COM.
CONTACT TB
key to enter the
OPEN-SHUT/ NC/8K2
main menu
OPEN-STOP-SHUT
CONTACT FI
AUTO. RECLOSING "PROG/OK"
NC/8K2
The number of
ON/OFF to change
the value CONTACT FS
manoeuvres PRE-FLASHING
NC/8K2
ON/OFF
carried out by
the operator
arm and the
SEQUENTIAL COM. CONTACT TB
OPEN-SHUT/ NC/8K2
ECU model are
OPEN-STOP-SHUT "PROG/OK"
CONTACT FI
always shown
AUTO. RECLOSING to change
NC/8K2
on the opening the value
ON/OFF
CONTACT FS
PRE-FLASHING
screen of the
NC/8K2
ON/OFF
display.
SEQUENTIAL COM. CONTACT TB
The plug
OPEN-SHUT/ NC/8K2
symbol
OPEN-STOP-SHUT
"PROG/OK"
CONTACT FI
AUTO. RECLOSING to change
indicates that the NC/8K2
ON/OFF the value
ECU is working CONTACT FS
PRE-FLASHING
NC/8K2
off mains power. ON/OFF
PRE-FLASHING
CONTACT FI
The fully
ON/OFF
NC/8K2
WARNING LIGHTS
charged battery
FIXED/ "PROG/OK"
CONTACT FS
INTERMITTENT to change
symbol NC/8K2
INDICATOR LIGHT the value
indicates that the
FIXED/ CONTACT CP
Note: 1
NC/8K2
INTERMITTENT
ECU is working
off battery power
at 100%.
WARNING LIGHTS CONTACT FS
FIXED/
75% NC/8K2
INTERMITTENT
"PROG/OK"
INDICATOR LIGHT
CONTACT CP
FIXED/
50% to change
NC/8K2
INTERMITTENT
the value
PHOTOCELL INVERT
25%
DURING CLOSING/ EXIT
Note: 2
AND IN STOP
0%
"PROG/OK"
to return to
INDICATOR LIGHT
FIXED/ 'safety devices'
INTERMITTENT
"PROG/OK"
PHOTOCELL INVERT
to change
DURING CLOSING/
the value AND IN STOP
TEST FI
Note: 3
ON/OFF
PHOTOCELL INVERT
DURING CLOSING/
AND IN STOP
"PROG/OK"
TEST FI
to change
ON/OFF
the value
TEST FS
Note: 3
ON/OFF
TEST FI
ON/OFF
TEST FS
"PROG/OK"
ON/OFF
to change
the value
GATE DELAY
DURING OPENING
Note: 4
ON/OFF
TEST FS
ON/OFF
GATE DELAY
"PROG/OK"
DURING OPENING
to change
ON/OFF
the value
ELECTRIC LOCK
Note: 5 ON/OFF
Notes:
1) The indicator light flashes slowly during opening, rapidly during closing; remains lit when the gate is blocked but not completely closed
GATE DELAY
and is off when the gate is completely closed.
ON/OFF
"PROG/OK" ELECTRIC LOCK
2) FI Mode:
to change
ON/OFF
the value - FI also active when the gate is blocked: If the photocells are in alarm and the gate is blocked, no movement commands will be accepted
MEMO RADIO
ON/OFF (even opening commands);
- FI active only during closing: In both cases activating the FI safety device during the closing stage will force travel direction inversion.
3) Photocell test (FI/FS)
ELECTRIC LOCK
If you enable the security test you will have to connect both the transmitter and the receiver to the controlled load output
ON/OFF
"PROG/OK"
REMOTE (CTRL 24 Vdc). When the test is enabled one second will pass between receiving a command and carrying it out.
to change
ON/OFF
the value
4) Opening direction gate delay
OUTPUT LC/CH2
RADIO CHANNEL/
If you enable gate delay the following will occur: during the opening movement gate leaf 1 moves first and then gate leaf 2. In the closing
COURTESY LIGHT
direction gate leaf 2 moves first then gate leaf 1. If gate delay is disabled both gate leaves move simultaneously.
5) Electric lock
MEMO RADIO
ON/OFF
If the electric lock is enabled the ELS output (binding post 8) will be activated before gate leaf 1 moves and will remain active until gate leaf
OUTPUT LC/CH2
1 has moved a few centimetres.
COURTESY LIGHT/
RADIO CHANNEL
"PROG/OK"
6) Select the type of motor
to return to EXIT
'options'
BL824 = articulated
BLi1000 = inside operator
BLTOW24 = articulated
OPTIONS OPTIONS
SAFETY DEVICES SAFETY DEVICES
MOTION MOTION
Arrow Arrow
DISPLAY DISPLAY
to scroll to scroll
REMOTE REMOTE
"PROG/OK" "PROG/OK" "PROG/OK"
to confirm to confirm to confirm
CONTRAST
MOTOR SELECTION
BL824
0....63
Note: 6
CURRENT SENSOR
"PROG/OK"
"PROG/OK" REAR LIGHTING "PROG/OK"
LEVEL 1...5
to change
to change to confirm
ALWAYS ON/60/30 SEC.
LIMITED OPENING
the value
the value
SETTING 1...5
EXIT
MOTOR SELECTION CONTRAST
BL824
0....63
"PROG/OK" "PROG/OK"
CURRENT SENSOR
to change to change "PROG/OK"
LEVEL 1...5
REAR LIGHTING
the value the value to change
ALWAYS ON/60/30 SEC.
LIMITED OPENING
the value
Note: 7
SETTING 1...4
EXIT
MOTOR SELECTION CONTRAST
BL824 0....63
"PROG/OK" "PROG/OK"
CURRENT SENSOR REAR LIGHTING
to change
to change
LEVEL 1...5
ALWAYS ON/60/30 SEC.
the value the value
LIMITED OPENING
Note: 8 EXIT
SELECTION 1...4
"PROG/OK"
to return to
CURRENT SENSOR
'display'
LEVEL 1...5
"PROG/OK" "PROG/OK"
LIMITED OPENING
to change to change
SETTING 1...5
the value the value
DIST. FROM CLOSE
Note: 9
STEPS 1...9
LIMITED OPENING
SETTING 1...5
"PROG/OK"
DIST. FROM CLOSE to change
the value
STEPS 1...9
GATE DELAY
Note: 10
STEPS 0...9
DIST. FROM CLOSE
"PROG/OK"
STEPS 1...9
to change
GATE DELAY
the value
STEPS 0...9
Note: 11
BRAKING ROOM
SETTING 1...3
GATE DELAY
STEPS 0...9 "PROG/OK"
to change
BRAKING ROOM
the value
SETTING 1...3
Note: 12
BRAKING SPEED
SETTING 1...3
BRAKING ROOM
SETTING 1...3
BRAKING SPEED
* * * * * * * * * * * * * * *
SETTING 1...3
* *
PAUSE TIME "PROG/OK" * PAUSE TIME *
130 SEC. to confirm
* 180 SEC. *
* *
* * * * * * * * * * * * * * *
BRAKING SPEED
SETTING 1...3
Press the arrows to increase or
PAUSE TIME
130 SEC. decrease the value (max. 240 sec).
"PROG/OK" Keeping the arrows held down will
to return to force the value to scroll rapidly.
EXIT
'motions'
BL224E = straight arm BL3924ERB = articulated (reversible)
BL1924ASW = articulated (without PRG) BLi924 = inside operator
BL3924ESB = articulated (self-locking) HL2524 = underground motor
18
• Set the main operating parameters (e.g. the presence of an electric lock ON/OFF) in the options menu.
• If you have safety devices working with 8.2k contacts select the correct setting from the safety device menu.
• Before programming the gate travel distances select the correct motor in the "Motion" menu.
OPTIONS
SAFETY DEVICES
MOTION
Arrow
DISPLAY
to scroll
CALENDAR
REMOTE
"PROG/OK"
to confirm "PROG/OK"
to toggle the
ENCODING: S4XX
value between
MEMORISE
* * * * * * * * * * * * * * *
S4XX & S500
* * CANCEL
* SET CONTRAST * Note: 13
CLEAR ALL MEMORY
26 SEC.
* *
CHANNEL FUNCTION
* *
* * * * * * * * * * * * * * * EXIT
ENCODING: S4XX
Press the arrows
"PROG/OK"
MEMORISE
to increase or
decrease the value CANCEL
(max. 63)
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
MEMORISE
"PROG/OK"
CANCEL
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
MEMORISE
CANCEL
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
MEMORISE
CANCEL
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
"PROG/OK"
MEMORISE
to return to
CANCEL
the remote
menu CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
Notes:
7) Current sensor settings:
- Level 1 = motor electrical input + 1 amp
- Level 2 = motor electrical input + 2 amps
- Level 3 = motor electrical input + 3 amps
The programmer checks the electrical input to the motor, detecting any
eventual increase in effort above the normal operating limits and intervenes
as an additional safety device.
8) Limited opening
Select from 1 to 4:
Selection 1 = 1/3 travel distance Gate 1
Selection 2 = 1/2 travel distance Gate 1
Selection 3 = 2/3 travel distance Gate 1
Selection 4 = entire travel distance Gate 1
9) Setting the distance from the opening travel limit:
To increase or reduce this distance modify the parameter in steps from 0
to 9. By default the appliance is set to level 4 and in this way the gate will
not slam against the travel limit but will stop within a centimetre of it.
10) Gate delay
To increase or reduce this distance modify the parameter in steps from
0 to 9. Setting the gate delay between the two gate leaves in opening and
consequently in closing.
11) Braking room
To increase or reduce this distance modify the parameter in steps from
0 to 3. Setting the braking room towards the end of the closing stage. The
default paramter is '0', i.e, disabled.
12) Braking speed
To increase or reduce this speed modify the parameter in steps from 0 to
9. Setting the braking speed during closing. The default paramter is '1' but
it only tales effect if paramter 11 "braking room" is set to 1, 2 or 3.
13) Encoding
Before changing the encoding type you must substitute the memory module,
changing from S4XX to S500 and viceversa, with the power switched off.
14) Channel functions
Each radio control channel can be
"A","B","C","D" set to one of 7 available functions:
- TD sequential command - TAL limited opening
- TA open - TC close
- Block - CH2 second radio channel - No command
Language choice:
• Press the right and left buttons simultaneously to enter the language submenu.
• Press the right and left buttons to change the language: Italian to English.
• Press the "PROG/OK" button to con rm the choice.
Arrow
to exit
MEMORISE
MEMORISE
PRESS the PRESS the
[Nr...] [Nr...]
transmitter the same
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
[AB--] channel transmitter
[AB--]
to confirm
* * to memorise * * channel
* ACTIVATION 1
* * ACTIVATION 2 * again
* *
* *
* * * * * * * * * * * * * * *
* * * * * * * * * * * * * * *
CANCEL
CANCEL
PRESS the PRESS the
[Nr...]
[Nr...]
transmitter the same
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
[AB--] channel transmitter
[AB--]
to confirm
* * to memorise * * channel
* ACTIVATION 1
* * ACTIVATION 2 * again
* *
* *
* * * * * * * * * * * * * * *
* * * * * * * * * * * * * * *
"PROG/OK"
EXIT
to confirm
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
CANCEL * CANCELLING
* * *
* ALL MEMORY ? * PRESS ok to * * * * * * * * * * * * * * *
* * * * * * * * * * * * * * * cancel all
memory
OK
or press exit
"PROG/OK"
CHANNEL A
to confirm
channel function A
CHANNEL B "PROG/OK"
to change
channel function B
the value
CHANNEL C
channel function C
Note: 14
CHANNEL D
channel function D
EXIT
PROGRAM
Flashing on the display. You have to enter the programming mode to program the system.
TB FI TA TD
FS CP TC TAL
During normal operation it indicates that the "automatic repositioning" procedure is about to
TB FI TA TD
take place. In this case any commands received (TA, TC, TAL or TD) will automatically start
FS CP TC TAL
OUT OF POS
this procedure.
This happens when an N.C. contact is activated (FI, FS, CP) during encoder programming or
STOP PROG
TB FI TA TD automatic repositioning. Once the passive state of the security devices has been reset the gate
FS CP TC TAL
will start moving again automatically. It also happens if a blackout occurs during programming.
AUTO PROG
Safety device test error. Check the condition of the safety devices and make sure that the
TB FI TA TD
alarm cuts in when an obstacle interferes with the beam (indication white characters on a black
FS CP TC TAL
background). In case of anomalies replace the damaged safety device or bridge the contact
SAFETY ERROR
and deactivate the safety test (option menu).
This occurs when the programmer sends a command to the motor and nothing happens (motor
TB FI TA TD
1/2 doesn't move). Check the Faston connections of motor 1/2 and the condition of the fuses
FS CP TC TAL
"F3", "F4" and then give another opening or closing command. If the motor still doesn't move
ERROR MOT1/2
you are faced with either a mechanical problem or a problem with the programmer.
Encoder count error motor 1/2 . If this error occurs during normal motor operation it means
TB FI TA TD
that there is a problem with one of the encoder signals. Check the relative connections and
FS CP TC TAL
carry out automatic repositioning.
ERROR ENC1/2
Encoder direction error motor 1/2 : The gate movement direction is different from the encoder
TB FI TA TD
setting (eg. the gate moves in the closing direction while the program is carrying out the
FS CP TC TAL
opening stage). Check motor 1/2 power supply connections.
ERROR DIR1/2
TB FI TA TD Current sensor error motor 1/2 . When the gate is not moving this symbol means there is a
FS CP TC TAL
problem with the current sensor 1/2 .
ERROR SENS1/2
Opening this contact will provoke a travel direction inversion during the closing stage and
TB FI TA TD
FS CP TC TAL
during the opening stage.
ACT. SAFETY EDGE
If the sensor intervenes during the opening direction the gate inverts the travel direction immediately
TB FI TA TD
and proceeds to the fully open position. If the sensor intervenes during the closing direction the gate
FS CP TC TAL
automatically inverts the travel direction of a few centimetres and then stops to free the obstacle.
ACTIVE SENSOR
19
PROGRAM
TB FI TA TD
FS CP TC TAL
00.000.007
CC2X24 V1.00
press both arrows
simultaneously to enter
the language submenu
ITALIANO
FRANÇAIS
ENGLISH
NEDERLANDS
DEUTSCH
MEMORISE
ESPAÑOL
[Nr...]
* * * * * * * * * * * * * * *
[AB--]
"PROG/OK" to confirm
* *
* CODE *
MEMORISED
* *
* * * * * * * * * * * * * * *
CANCEL
[Nr...]
* * * * * * * * * * * * * * *
[AB--]
* *
* CODE *
CANCELLED
* *
* * * * * * * * * * * * * * *
Operational indications
Pause time programming or pause for
PAUSE
automatic reclosing (if activated)
TB FI TA TD
FS CP TC TAL
Automatic programming under way
AUTO PROG
TB FI TA TD
FS CP TC TAL
Opening stage
OPENING
TB FI TA TD
FS CP TC TAL
Block during opening
STOP OPENING
TB FI TA TD
FS CP TC TAL
CLOSING Closing stage
TB FI TA TD
FS CP TC TAL
Block during closing
STOP CLOSING
TB FI TA TD
FS CP TC TAL
Alarm indications