I Disc Playback; Basic Playback; Cancelling And Calling Back Pbc Function (Vcd); Hdmi Setup - Denon DVD-1920 Bedienungsanleitung

DISC PLAYBACK

Basic Playback

DVD-V DVD-A VCD
Getting started
• Turn on the power of the TV, amplifier and any other com-
ponents which are connected to the DVD player.
• Make sure the TV and audio receiver (commercially avail-
able) are set to the correct channel.
1 Press the POWER ON button.
• P-ON will appear briefly on the dis-
play panel.
2 Press the OPEN/CLOSE button
to open disc loading tray.
3
Place the disc on the tray, with
the label facing up.
4 Press the PLAY button.
• The tray will close automatically, then playback will start
from the first chapter or track of the disc. If the playback
does not start automatically, press the PLAY button.
• When you play back the DVD with a title menu, it may
appear on the screen. In this case, refer to "Title
Menu".
5
Press the STOP button to stop playback.
NOTES:
• A "prohibited icon" may appear at the
top-right on the TV screen during opera-
tion, warning that a prohibited operation
has been encountered by the DVD play-
er or the disc.
• With DVDs that use some titles for playback pro-
gramme signals, playback may start from the second
title, or it may skip these titles.
• During the playback of two layered disc, pictures may
stop for a moment. This happens when the 1st layer
switches to the 2nd layer. This is not a malfunction.
• The operation may vary when you play back DVDs with
disc menu or Video CDs with PBC. Refer to the manual
accompanying the disc for details.
CANCELLING AND CALLING BACK PBC FUNCTION
1 Insert a Video CD.
Press the STOP button.
2
Press the Numeric buttons to enter the desired
3
Track number.
• PBC function is now cancelled and the playback of the
Video CD will start.
4 To call back PBC function, press the STOP button
twice, and then press the PLAY button.
• The title menu will appear on the display.

HDMI Setup

1 Press the HDMI button on the front panel to select
the HDMI output mode.
The output mode changes as follows every time
the HDMI button is pressed.
• The HDMI indicator on the front panel lights up when
HDMI output mode is on.
OFF 480/576P
OFF (Default): No video outp
480/576P: Video output from the HDMI OUT jack at 480/576p.
720P: Video output from the HDMI OUT jack at 720p.
1080: Video output from the HDMI OUT jack at 1080i.
NOTES:
• Video and audio signals may be distorted temporarily
when switching to/from the HDMI output mode.
Super
CD MP3
Audio CD
JPEG WMA DivX
VCD
720P 1080
uts from the HDMI OUT connector.
• Use a display equipment with an HDMI-compatible port.
• Progressive video signal will not be output from the COM-
PONENT VIDEO OUT during the HDMI output mode.
• The HDMI indicator on the front panel flashes when you
select the HDMI output mode but there is no HDMI cable.
®
• If you turn on the pure direct mode, both video and
audio signals through the HDMI output will be cut off
(press the PURE DIRECT button again to recover).
• You can check the HDMI connection status by pressing
the DISPLAY button during playback with the HDMI
output mode (refer to page 25).
• If the TV is not compatible with newly selected HDMI
output mode, the actual output mode will be kept the
one before changing the selection. When this occurs,
the newly selected mode will appear on the front panel
display (see page 11) while the actual output resolution
will be indicated by performing the on-screen display as
described on pages 24-25.
• Actual output signals for each HDMI mode are differ
with the compatibility of the connected display device.
Refer to the table on page 11 for details of output pat-
terns of each HDMI mode.

Pure Direct Mode

1 Press the PURE DIRECT button on the front panel to
output an analog audio signal only (no analog video
and HDMI signals will be output and the display will be
turned off). The higher quality sound will be achieved.
NOTES:
• When the buttons below are pressed, the pure direct
mode will be released.
OPEN/CLOSE button (on both the remote and the front
panel), SETUP or DISPLAY button (on the remote),
ON/STANDBY or PURE DIRECT button (on the front panel).
• The PURE DIRECT button will not function while dis-
playing the setup menu.
• If you turn on the pure direct mode while selecting HDMI
mode, both video and audio signals will not be output.

Brightness of the Front Panel Display

1 Press the DIMMER button on the front panel to
select the desired brightness of the front panel dis-
play. (BRIGHT, DIMMER or OFF)
• The default setting is BRIGHT.
NOTES:
• The brightness of the front panel display can be adjust-
ed from the setup menu. Details are on page 31.
• When you turn on the power next time, the brightness
of the front panel display will be as set in setup menu.

General Features

DVD may contain menus to navigate the disc and access spe-
cial features. Press the appropriate Numeric buttons or use the
Cursor buttons (K / L / s / B) to highlight your selection in the
DVD main menu and press the ENTER button to confirm.
NOTE:
• Unless otherwise stated, all operations described are
based on remote control use. Some operations can be
carried out using the menu bar on the TV screen.

Disc Menu

1 Press the MENU button.
• The DVD main menu will appear.
2
If the feature is not available,
appear on the TV screen.
3 If disc menu is available on the disc, audio
language, subtitle options, chapters for the title and
other options will appear for selection.
4
Press the Cursor buttons (K / L / s / B) to select an
item, and the ENTER button to confirm the selection.
– 17 –
DVD-V DVD-A
DVD-V
symbol may
EN