Cleaning And Maintenance - Thetford C-250 Bedienungsanleitung

water in the toilet bowl. Failure to adhere to this notice
may result in water damage to your caravan or motor
home.
Using the toilet with Optional Features
1. Electric blade opener: Push the electric blade button on
the control display to electrically open or close the blade.
In the case of failure, you can manually open or close the
blade by sliding the small handle under the toilet bowl
sideways.
14. Automatic ventilator: The ventilator automatically
starts when the control panel is activated (by pressing
the flush button) and will automatically shut off after
approximately 5 minutes. The automatic ventilator
indicator will flash until automatic shut-off occurs. If you
want to stop the ventilator, press the automatic ventilator
button. If you want to re-start the ventilator, press the
button again (the LED will start flashing again).
15. Flush water tank level indicator (only for toilets with
own flush-water tank): When the flush water tank level
indicator lights up, refill the flush-water tank, as only
about 1.5 litres of water is left in the tank, which is
sufficient for approximately 2 flushes.
EMPTYING
The waste-holding tank has a capacity of 18 litres and
requires emptying when the red light (LED) on the toilet
control display lights up, when the waste-holding tank only
has capacity for approximately 2 more litres, which is no
more than two to three further uses.
UK
Make sure that the blade is closed. Open the access door
located outside the vehicle, pull the safety catch upwards and
remove the waste-holding tank.
16. Place the waste-holding tank in an upright position
(pull-out handle at the top, wheels at the bottom).
Slide the handle sideways - to the front of the tank - until
it snaps out of its locked position.
17. Pull the handle up and wheel the waste-holding tank to
an authorized waste disposal point.
18. Push the handle back into its locked position. Turn the
emptying spout upwards and remove the cap from
the spout. Hold the waste-holding tank in such a way
that during emptying you can operate the vent plunger
with your thumb. To empty the tank without splashing,
depress the vent plunger while emptying the tank. After
emptying, rinse the tank and blade thoroughly with water.
W arning! Do not seriously shake the tank or use high
pressure water cleaners. This may cause damage to the
tank's interior.
N ote. The vent plunger should only be depressed once
the emptying spout is pointing downwards. Prepare the
toilet for re-use if required. Slide the waste-holding tank
into the toilet and close the access door.
Emptying with Optional Features
19. waste-holding tank multi-level indicator: The lower lamp
indicates that the waste-holding tank is almost empty; the
middle lamp indicates that it is more than half full; when
the upper lamp lights up, the tank needs emptying as it
can only take 2 -  further uses.
N ote. The waste-holding tank level indicator will flash
when the holding tank is not present. In this case the
toilet will not flush.
20. Waste pump-out system: When activating the control
panel this feature automatically lights up. When the
waste-holding tank level indicator illuminates, press the
Waste pump-out button to pump out the waste from the
holding tank into the vehicle's waste tank. The button
will flash while the waste is being pumped and will stop
automatically (after approximately 5 minutes) when all
waste has been transferred. If the vehicle's waste tank
is full, the waste pump-out light will flash rapidly and
no pump-out will be possible until the central tank is
emptied. (Check the level of the vehicle's waste tank on
the vehicle's central console). After the waste-holding
tank has been emptied, there will be approximately 1.5
litres of waste left in the tank. This is normal. Add 2 litres
of water and a correct dosage of Thetford toilet fluids to
the waste-holding tank.
I mportant! It is vital that the correct amount of toilet
fluid is added to ensure the proper breakdown of the
waste in the holding tank. Only use the system when the
tank is full. Using the system too often on an empty tank
can cause damage to the pump, which could cause the
system to fail.
CLEANING AND MAINTENANCE
The toilet should be cleaned and maintained regularly,
depending on the amount of use. To clean Thetford toilets,
we advise using water and Thetford Bathroom Cleaner.
Note. Never use bleach, vinegar or other powerful household
cleaners that contain these substances. These may cause
permanent damage to the seals and other toilet components.
Toilet Bowl
- Squirt Thetford Bathroom Cleaner into the toilet bowl.
- Flush the toilet bowl with water and wipe down the rest
of the toilet with a damp cloth.
- Clean seat and lid The seat and lid can easily be
removed: Lift the seat and lid assembly and pull the
round pins (inside the assembly) outwards from the
pin holes. After cleaning, replace the seat and lid by
positioning the round pins in front of the pin holes and
push the lid and seat downwards.
- To keep your flush water fresh and to prevent deposits
from forming in your toilet bowl, add a correct dosage of
Aqua Rinse in your flush water tank, if present, on your
toilet.
Tip! For a really shining toilet, dry with a soft dry cloth after
cleaning.
- 4 -