Additional Safety Instructions - VONROC TS501AC Bersetzung Der Originalbetriebsanleitung

EN
15. Unplug the power tool from the power outlet.
• When you are not using the power tool, when
you conduct maintenance and when you chan-
ge your tools such as blades, drills and cutters.
16. Do not leave the key inside the tool.
• Before switching it on, make sure that keys and
setup tools have been cleared
17. Avoid unintentionally switching the power tool on.
• Verify that while connecting the plug into the
socket that the power is off.
18. Use the extension cables while outdoors.
• When using the power tool outdoors make sure
to use the appropriate and approved labeled
extension cable.

ADDITIONAL SAFETY INSTRUCTIONS

1. When using the saw blades with hard metal
teeth (Carbon tipped) it is advisable to use bla-
des with a negative or slightly positive cutting
angle. Do not use any saw blades with deeply
cut teeth. They can grip the protective cap.
2. Attention: First carefully assemble all the parts
before starting work. Follow the procedure as
indicated.
3. If you are not familiar with using such a machi-
ne, you would be better to be informed first by a
professional, an instructor or by a technician.
4. Always clamp or press the workpiece firmly
against the saw guide, before you carry out the
process. The use of all possible clamping set-
ups is preferable to using your hands.
5. Important: If you are holding the workpiece by
hand for the process to be carried out, keep a mi-
nimum distance of 100 mm from the saw blade.
6. Always press the workpiece against the bench.
7. Keep the saw blade sharp and check regular-
ly whether it rotates freely without abnormal
vibrations. Replace the saw blade if necessary.
8. Allow the machine to rotate freely until it
reaches the maximum number of revolutions,
before you start the process.
9. Maintain the air inlets at the back and the
bottom of the bench saw machine and electric
motor for a longer machine life. Dust piles must
be removed.
10. Always lock the different degree set-ups before
you start processing.
11. Only buy suitable saw blades with a number of re-
volutions of at least 6000 revolutions per minute.
12. Only use the correct saw blade. Too small or too
big saw blades are extremely dangerous.
10
13. Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14. Grease the new saw blade and clean the flan-
ges before you assemble the new blade. Then
assemble the blade in the correct direction and
pull the flanges firmly using the central bolt.
15. Only use original flanges. All other types are not
suitable.
16. Never work without the protective cap of the
saw blade.
17. The moving part of the protective cap must also
remain assembled.
18. Never grease the saw blade while it is rotating.
19. Always keep your hands removed from the track
of the saw blades.
20. Never pick up the workpiece by grasping with
your hands along or behind the saw blade.
21. Ensure that the workpiece never touches the saw
blade before the machine has been switched on.
22. Never process metal or stone sorts with this
machine.
23. Use support aids in order to support long work-
pieces.
24. Never use the machine in a dangerous environ-
ment, where inflammable gases or fluids are
present.
25. Never leave the machine unattended without
first disconnecting it from the mains voltage.
26. If you hear abnormal noises, try to trace them
or take the machine to a recognized fitter, or
repair company.
27. If a part is broken or damaged, replace it or
repair it immediately.
28. Never stand in the track of the saw blade but
stand to the left or the right of the saw bench.
29. Your hands must likewise be placed next to the
track of the saw blade.
30. Always use the push stick instead of your hands
to push the wood through the saw.
31. Always place the wood at the front of the saw
bench and then push it further back.
32. For mitring only the adjustable guide must be
used and the fence must be removed.
33. Never use the fence as a linear measure for
cutting off beams.
34. If the saw blade is locked: first switch off the
machine before you attend to the fault.
35. Avoid workpieces hitting back in your direction
by taking the following measures:
• Always use sharp saw blades.
• Do not saw too small workpieces.
WWW.VONROC.COM