VONROC TS501AC Bersetzung Der Originalbetriebsanleitung Seite 12

EN
Sawblade specifications:
Diameter
Base blade thickness
Width of cut
Bore diameter
Number of teeth
Max. workpiece height 90º
Max. workpiece height 45º
Thickness of the riving knife
Weight
Lpa (sound pressure level)
Lwa (sound power level)
Vibration value
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardised test given in EN 60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
- the times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-6.
1. Saw table with two rulers
2A. Parallel guide
2B. Guide extension
2C. Wing nuts
3. Extensions (2 pcs)
4. Dust extraction
5. Guard
6. Mitre guide
7. Push stick
8. On/off switch
9. 2 in 1 adjustment handle
10. Locking knob
11. Electric plug
12
Ø 210 mm
1.8 mm
2.8 mm
Ø 30 mm
40T
70 mm
45 mm
2.0 mm
14.5 kg
99.6 +3 dB(A)
112.6 +3 dB(A)
<2.5 m/s2
12. Ruler sawblade angle
13. Extension support (4 pcs)
14. Wrenches (2 pcs)
15. Legs (4 pcs)
16. Long bolts with nuts (8 pcs)
17. Small bolts with nuts for extensions (8 pcs)
18. Dust extraction connection
19. Sawblade guard knob
20. Riving knife
21. Saw table inlay
22A. Cross strut long (2 pcs)
22B. Cross strut short (2 pcs)
23. Rubber feet (4 pcs)
24. Additional legs (2 pcs)
25. Small bolts with nuts for cross strut (16 pcs)
26. Small bolts with nuts for additional legs (4 pcs)
27. Connection vacuum cleaner
28. Fixing screw
29. Carriage-type bolts with nuts
30. Holder clips
3. ASSEMBLY
Assembly of the undercarriage (Fig A4)
First assemble all parts before firmly
tightening all bolts.
• Put the machine upside down. Put a piece of
cardboard underneath, so you don't damage
the subsurface.
• Mount the legs (15) (4 pcs) with one extension
support (13) (4 pcs) per leg on the four corners
of the body, use longer bolts (16) with nuts (2
pcs per leg) (Fig.B1)
• Make sure the extension supports (13) are
mounted in the same way as shown in Fig.B1
• Mount Cross strut long (22A) (2 pcs) between
the legs on the front and back side of the ma-
chine. Use small bolts (25) with nuts (8 pcs).
• Mount Cross strut short (22B) (2 pcs) between
the legs on both sides of the machine. Use
small bolts (25) with nuts (8 pcs).
• Place the rubber feet (23) (4 pcs)
• Mount the additional legs (24) (2 pcs) on the
backside of the machine, use small bolts (26)
with nuts (4 pcs)
Assembly of the extensions (Fig B1)
Machine is still upside down
• Mount the extensions (3) (2 pcs) to the table,
use small bolts (17) with nuts (4 pcs).
WWW.VONROC.COM