Operation - VONROC TS501AC Bersetzung Der Originalbetriebsanleitung

• Mount the extensions support (13) to the ex ten-
sions (3), use small bolts (17) with nuts (4 pcs)
• Turn the machine back on its feet. Make sure
the extensions are levelled with the table, by
using the slots in the extensions supports.
Assembly of the riving knife (Fig A4, C)
• Remove the inlay (21) from the table, by using a
screwdriver (Fig.G1).
• Loosen the fixing screw (28)(Fig.C1)
• Raise the riving knife until the depth between
the saw table and the upper edge of the riving
knife equals approx. 110mm (Fig.C2)
• The distance between the riving knife and the
toothed rim of the saw blade must be between
3 and 5 mm (Fig.C3).
• The tip of the riving knife shall not be lower than
5 mm from the tooth peak, as shown in Fig.C3.
Attachment of the guard (Fig C4)
• Turn sawblade completely upwards (instructi-
ons for height adjustment see chapter 4).
• Pull the knob (19) of the guard (5) and place it
over the riving knife (20) while pulling the knob.
• Release the knob and make sure the pin slides
in the hole.
• Secure the guard by tightening the knob.
Assembly of the dust extraction (Fig. D)
• Assemble dust extraction like shown on Fig.D
• Attach the vacuum cleaner to the vacuum clea-
ner connection (27)(Fig.D)
Attachment of the parallel guide (Fig E)
• Attach the parallel guide (2A) on the right side
off the saw blade on the table.
• Lock the guide down by pushing down the
handle (Fig.E)
Attachment of the parralel guide holder (Fig. I)
The parallel guide can be stored using the holder
clips (30). Mount the holder clips (30) using carri-
age-type bolts with nuts (29). The holders can be
mounted as shown in Fig I1 or as shown in Fig I2.
Attachment of the mitre guide (Fig A1)
• Slide the guide in the slot of the table at the left
side of the sawblade Fig.A1
WWW.VONROC.COM
Assemble or change the saw blade (Fig G)
First remove the plug from the mains before
the saw blade is assembled or replaced.
The arrow marked on the saw blade, which
indicates the direction of rotation, must point
in the same direction as the arrow marked on
the machine, the saw blade teeth must point
downwards on the front of the saw.
• Remove the inlay (21) from the table, by using a
screwdriver. Fig.G1
• Turn the saw blade completely upwards. (In-
structions for height adjustment see chapter 4)
• Loosen the nut with the wrenches (14) (Fig.G2)
• Remove the nut and the outside flange from the
sawblade axle. (Fig.G3)
• Slide the old saw blade over the saw blade axle
and put on a new saw blade.
• Put the outside flange back on add the nut.
• Tighten the nut by using the wrenches.
• Put the inlay back in the table and tighten the
screw.

4. OPERATION

Switching on/off (Fig A1)
• Press the switch into position '1' to put your
machine into operation.
• To switch off the machine the same switch
needs to be pressed to position '0'
• Always keep the mains cable away from moving
parts.
Using the 2 in 1 handle, Adjust the angle and
height of the saw blade (Fig A2)
Using the height adjustment
• Turn the handle (9) clockwise to raise the saw-
blade.
• Turn the handle counter clockwise to lower the
sawblade.
• Make sure the saw blade is always approxima-
tely 2 mm higher than the total thickness of the
material to be sawn.
Using the angle adjustment (Fig G4)
• Slightly loosen the knob(10)
• Press the handle(9) towards the machine and
turn counter clockwise to adjust the sawblade
in its angle.
• Fasten the knob(10)
EN
13