Remote Control; Hi-Power Operation - Toshiba RAS-B10J2FVG-E Bedienungsanleitung

INDOOR UNIT DISPLAY & UNIT
1
OPERATION PANEL
This indoor unit can be operated with the unit operation panel or using remote
control.
Operational contents will be followed the one which was operated later.
If change the set temperature with operation panel of unit, temperature
indication will be changed, but the temperature display on the remote control
will not change. If set the air fl ow only with the upper port, a little air fl ow may
happen at the lower port.
6 7 8
%
&
! " #
OPERATION button : Unit operation ON/OFF button, turn off FILTER
1
CHECK Indicator.
MODE button : Operation mode (Auto→Cooling→Heating→Auto→ • • • )
2
w CHILD LOCK function : Press MODE button for 3 seconds. (It is
possible to operate even when stopping.)
To cancel CHILD LOCK function, press MODE button for 3 seconds
once again.
When CHILD LOCK function is activated, 3 beeps will sound.
When press MODE button to cancel the function, a beep will sound and
then 3 seconds later 3 beep sound may occur.
The indicator button will be invalid while the child lock function is
activated. (When press the button, 1 beep will sound).
Operation with remote control during the CHILD LOCK function works.
This function is cancelled when the power supply is off or failure.
AIR OUTLET SELECT button : Cooling, Auto (Upper & Lower→Upper→
3
Upper & Lower→ • • •)
Dry (upper only)
Heating (Upper & Lower→Upper→Lower→Upper & Lower→ • • •)
On cooling operation, whichever air outlet is set, only Upper is used
when the room temperature approaches the set temperature.
During stop operation : Open/close the lower air outlet grille.
When the TEMPERATURE indicator display "CL" the lower air outlet
grille will be in closed status.
When the TEMPERATURE indicator display "OP" the lower air outlet
grille will be in open status.
TEMPERATURE button (Up) : Setting temperature increase by 1°C
4
(17°C→ 18°C→ • • • 30°C)
TEMPERATURE button (Down) : Setting temperature decrease by 1°C
5
(30°C→29°C→ • • • 17°C)
COOL and DRY indicator (Blue)
6
HEAT indicator (Orange)
7
Refrigerant leak detection sensor (Green)
8
Require connecting refrigerant leak detection sensor which available as
w
accessory. Please inquire the dealership.
OPERATION or FAN ONLY indicator (Green)
9
HI-POWER indicator (Green)
!
FLOOR indicator (Orange)
"
TIMER indicator (Yellow)
#
FILTER CHECK indicator (Red)
$
TEMPERATURE indicator (Blue)
%
AIR OUTLET indicator (Green)
&
2 PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the attachment fi lters (see detail in the
accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new alkaline batteries (AAA type)
following the (+) and (–) positions.
Removing the batteries
1. Remove the cover, and take out the batteries.
2. Reattach the cover.
• Please dispose of the batteries according to
the local regulation.
Clock Setup
1. Push CLOCK by tip of the pencil. If timer
indication is fl ashing, go to the next step 2.
2. Press or : adjust the time.
3. Press : Set the time.
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
9 2
1
4
5
Remote control light
receiver
$ 3
Insert direction of
(+) and (-) correctly
Pull the cover
away fi rmly.
Upper air
outlet grille
Main operation
part
Lower air
Air inlet grille
outlet grille
3 AIR FLOW DIRECTION
Press : Move the louver in the
1
desired vertical direction.
Press : Swing the air automatically
2
and press again to stop.
3
For horizontal direction, adjust manually.
Note:
• Do not move the vertical louver manually by others.
• The vertical louver may automation positioning by some operation mode.
• On heating operation, in case of AIR OUTLET SELECT is set as Lower,
upper louver is not operate even if swing is set by remote, though
receiving history is recorded.
• When changed the air fl ow to up/down or upward blowing, the swing
operation will be performed.
• At the time of FLOOR WARMING OPERATION, the air will blow
downward only and it cannot order to swing operation with remote
control.
4

REMOTE CONTROL

1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 Weekly timer setting button
9 Memory and Preset button (PRESET)
! Fireplace/8°C heating operation button (
" High power button (Hi-POWER)
# Economy button (ECO)
$ Comfort sleep button (COMFORT SLEEP)
% Floor warming mode button (FLOOR)
& Clock Reset button (CLOCK)
( Check button (CHECK)
) Reset button (RESET)
~ Filter reset button (FILTER)
+ Power selection/Silent operation (outdoor
unit) button ( / )
AUTOMATIC / COOLING (DRY) /
5
HEATING / FAN ONLY OPERATION
1. Press : Select Auto A. Cool
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
3. Press : Select AUTO, LOW , LOW+
HIGH , and Quiet ( ).
AUTOMATIC OPERATION : Choose cooling or heating operation
w
automatically.
In DRY OPERATION mode, it can not select air volume.
w
6

Hi-POWER OPERATION

To automatically control room temperature and airfl ow for faster Auto, cooling
or heating operation (except in DRY mode).
Press : Start and stop the operation.
1
9
4
2
/8°C)
6
3
5
7
%
#
"
!
+
$
8
& )
( ~
, Dry , Heat or Fan only .
, MED , MED+ ,