Surround - Denon AVR-3805 Bedienungsanleitung

[1] Outputting a program source to an amplifier, etc., in a different room (ZONE2, ZONE3 mode)
1
Press the "ON" button.
(Main unit)
2
Press the ZONE2/3/REC
button.
The display switches as
follows each time the button
is pressed.
(Main unit)
ZONE2 ZONE3
(RECOUT)
3
With "ZONE2 SOURCE"
displayed, turn the
FUNCTION knob and select
the source you wish to
output.
(Main unit)
• The display switches the
selected source.
• ZONE3 can also be set with a method similar to the
above.
[2] Remote control unit operations during multi-source playback (selecting the input source)
This operation is not possible in the REC OUT mode.
1
Select "ZONE2" using the
ZONE2/ZONE3 button.
(Remote control unit)
2
Press the "SOURCE ON"
button.
To cancel the ZONE2
mode.
(Remote control unit)
Press the ZONE2
"SOURCE OFF" button.
3
Press the input source button
• The ZONE2 source switches directly.
4
The output level of the ZONE2
OUT terminals can be
controlled using the VOLUME
+ and - buttons on the remote
control unit.
(Remote control unit)
The output level of ZONE2
OUT can be controlled only if
ZONE2 vol. level is set "Variable" at Zone2
Control in System Setup Menu. (see page 27)
DEFAULT SETTING (ZONE2 VOLUME
LEVEL) :
- - - dB (MINIMUM)
• ZONE 3 can also be set with a method similar to the
above.
3
2 1
F U N C T I O N
Z O N E 2 S O U R C E
4
Start playing the source to be output.
• For operating instructions, refer to the
manuals of the respective components.
NOTES:
• The signals of the source selected in the ZONE2
mode are also output from the VCR-1, VCR-2 and
CDR/TAPE recording output jacks.
• Digital signals are not output from the ZONE3, audio
(FIXED-OUT) output jacks and ZONE2 audio output
jacks.
• Refer to page 40 about the MULTI ZONE
connections.
2
1
5 4
5
When the ZONE2 SOURCE
function is set to TUNER, the
preset channel can be
selected using the CHANNEL
+ and - buttons on the
remote control unit. (Remote control unit)
NOTE:
• The main zone output can be turn on and off
"SOURCE ON/OFF"button (AMP mode)
11

SURROUND

Before playing with the surround function
• Before playing with the surround function, be sure to use the test tones to adjust the playback level from the
different speakers. This adjustment can be performed with the system setup (see page 20) or from the remote
control unit, as described below.
• Adjusting with the remote control unit using the test tones is only possible in the "Auto" mode and only
effective in the STANDARD (DOLBY/DTS SURROUND) modes. The adjusted levels for the different modes
are automatically stored in the memory.
1
Press the TEST TONE button.
(Remote control unit)
2
Test tones are output from
the different speakers. Use
CH SEL
ENTER
the channel volume adjust
buttons to adjust so that the
volume of the test tones is
(Remote control unit)
the same for all the speakers.
3
After completing
adjustment, press the TEST
TONE button again.
(Remote control unit)
• After adjusting using the test tones, adjust the channel levels either according to the playback sources or to
suit your tastes, as described below.
1
Select the speaker level you
want to adjust.
CH SEL
ENTER
(Remote control unit)
The channel switches as shown below each
time the button is pressed.
FL C FR SR SBR SBL
FADER SW SL
2
Adjust the level of the
selected speaker.
CH SEL
ENTER
(Remote control unit)
When the surround back speaker setting is set
to "1spkr" for "Speaker Configuration", this is
set to "SB".
the
1, 3
RC-970
2
NOTES:
• The adjustment range for the different channels
is +12 dB to –12 dB.
• The sound from the subwoofer can be cut by
lowering the SW (subwoofer) setting one step
from –12 dB (setting it to "OFF").
ENGLISH
2
1
41