Denon AVR-1404 Bedienungsanleitung Seite 16

ENGLISH
3
Select the play mode.
Press the SURROUND MODE button, then turn
the SELECT knob.
Example: Stereo
(Main unit) (Remote control unit)
To select the surround mode
while adjusting the surround
parameters, channel volume
or tone control, press the
surround mode button then
operate the selector.
4
Start playback on the selected component.
• For operating instructions, refer to the
component's manual.
5
Adjust the volume.
The volume level
is displayed on
(Main unit) (Remote control
the master
unit)
volume level
display.
The volume can be adjusted within the
range of –60 to 0 to 18 dB, in steps of 1 dB.
However, when the channel level is set as
described on page 18, if the volume for any
channel is set at +1 dB or greater, the
volume cannot be adjusted up to 18 dB. (In
this case the maximum volume is adjusted
to "18 dB — (Maximum value of channel
level)".)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs
are played in the "ANALOG" or "PCM" mode.
When playing DTS-compatible sources, be sure to
connect the source component to the digital input
jacks (OPTICAL/COAXIAL) and set the input mode
to "DTS".
16
Input mode display
One of these lights,
depending on the input
• In the AUTO mode
signal.
INPUT
AUTO PCM DTS
DIGITAL
• In the DIGITAL PCM mode
INPUT
AUTO PCM DTS
DIGITAL
• In the DIGITAL DTS mode
INPUT
AUTO PCM DTS
DIGITAL
• In the ANALOG mode
INPUT
AUTO PCM DTS
(Main unit)
Input signal display
• DOLBY DIGITAL
SIGNAL
DIGITAL
• DTS
SIGNAL
DIGITAL
• PCM
SIGNAL
DIGITAL
The indicator lights when digital signals
DIGITAL
are being input properly. If the
does not light, check whether the digital input
component setup (page 12) and connections are
correct and whether the component's power is
turned on.
NOTE:
• The indicator will light when playing
DIGITAL
CD-ROMs containing data other than audio
signals, but no sound will be heard.
After starting playback
[1] Adjusting the sound quality (tone)
ANALOG
1
The tone switches as follows each time the
TONE CONTROL button is pressed.
(Main unit)
ANALOG
2
With the name of the volume to
be adjusted selected, turn the
SELECT knob to adjust the level.
• To increase the bass or treble: Turn the
control clockwise. (The bass or treble sound
can be increased to up to +10 dB in steps of
2 dB.)
• To decrease the bass or treble: Turn the
control counterclockwise. (The bass or treble
sound can be decreased to up to –10 dB in
steps of 2 dB.)
[2] Listening over headphones
1
Connect the headphones to
indicator the PHONES jack of the front
DIGITAL
panel.
2
Press the SPEAKER A or B
button turn the speaker off.
CAUTION: No sound is produced from the
headphones when speakers A or B
are turned on.
[3] Turning the sound off temporarily (muting)
1
Use this to turn off the audio
output temporarily.
Press the MUTING button.
Cancelling MUTING mode.
• Press the MUTING
button again.
• Muting will also be cancelled when
MASTER VOL is adjusted up or down.
BASS TREBLE
3
(Main unit)
3
If you do not want the bass and treble to be
adjusted, turn on the tone defeat mode.
(Main unit)
NOTE:
To prevent hearing loss, do not raise the volume level
PHONES
excessively when using headphones.
1
2
(Main unit)
(Remote
control unit)
2 1
The signals do not pass
through the bass and treble
adjustment circuits, providing
higher quality sound.
1