Functional Description - Makita 9564HR Bedienungsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function
on the tool.
Shaft lock
CAUTION:
Never actuate the shaft lock when the spindle is
•
moving. The tool may be damaged.
Fig.1
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
Switch action
CAUTION:
Before plugging in the tool, always check to see that the
•
slide switch actuates properly and returns to the "OFF"
position when the rear of the slide switch is depressed.
Switch can be locked in "ON" position for ease of
•
operator comfort during extended use. Apply caution
when locking tool in "ON" position and maintain firm
grasp on tool.
Fig.2
To start the tool, slide the slide switch toward the "I (ON)"
position by pushing the rear of the slide switch. For continuous
operation, press the front of the slide switch to lock it.
To stop the tool, press the rear of the slide switch, then
slide it toward the "O (OFF)" position.
Indication lamp
Fig.3
The indication lamp lights up green when the tool is plugged. If
the indication lamp does not light up, the mains cord or the
controller may be defective. The indication lamp is lit but the
tool does not start even if the tool is switched on, the carbon
brushes may be worn out, or the controller, the motor or the
ON/OFF switch may be defective.
Unintentional restart proof
The tool does not start with the switch being lock-on
even when the tool is plugged.
At this time, the indication lamp flickers red and shows
the unintentional restart proof device is on function.
To cancel the unintentional restart proof, return the slide
switch to "O(OFF)" position.
Soft start feature
Soft start feature suppresses starting shock.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the tool.
Installing side grip (handle)
CAUTION:
Always be sure that the side grip is installed
•
securely before operation.
Fig.4
Screw the side grip securely on the position of the tool
as shown in the figure.
Installing or removing wheel guard
(For depressed center wheel, flap disc, flex
wheel, wire wheel brush / abrasive cut-off
wheel, diamond wheel)
WARNING:
When using a depressed center wheel, flap disc,
•
flex wheel or wire wheel brush, the wheel guard
must be fitted on the tool so that the closed side of
the guard always points toward the operator.
When using an abrasive cut-off / diamond wheel, be
•
sure to use only the special wheel guard designed for
use with cut-off wheels. (In some European countries,
when using a diamond wheel, the ordinary guard can be
used. Follow the regulations in your country.)
For tool with clamp lever type wheel guard
Fig.5
Loosen the screw, and then pull the lever in the
direction of the arrow. Mount the wheel guard with the
protrusions on the wheel guard band aligned with the
notches on the bearing box. Then rotate the wheel
guard to such an angle that it can protect the operator
according to work.
Fig.6
Pull the lever in direction of the arrow. Then tighten the
wheel guard with fastening the screw. Be sure to tighten
the screw securely. The setting angle of the wheel
guard can be adjusted with the lever.
To remove wheel
procedure in reverse.
For tool with locking screw type wheel guard
Fig.7
Fig.8
Mount the wheel guard with the protrusions on the
wheel guard band aligned with the notches on the
bearing box. Then rotate the wheel guard to such an
angle that it can protect the operator according to work.
Be sure to tighten the screw securely.
To remove wheel
procedure in reverse.
Installing or removing depressed center
wheel or flap disc (optional accessory)
WARNING:
When using a depressed center wheel or flap disc, the
•
wheel guard must be fitted on the tool so that the closed
side of the guard always points toward the operator.
8
guard, follow the installation
guard, follow the installation