Ec Declaration Of Conformity; Safety Warnings - Makita DUB184 Betriebsanleitung

Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN 0
Work mode: operation without load
Vibration emission (a ) : 2. m/s
h
Uncertainty (K) : 1. m/s
NOTE: The declared vibration total value(s) has been
measure d in a c c or d an c e w it h a stan d ar d test met h o d
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
The vibration emission during
WARNING:
actual use of the po er tool can differ from the
declared value(s) depending on the ays in hich
the tool is used especially hat kind of orkpiece
is processed.
Be sure to identify safety mea-
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times hen the tool is s itched
off and hen it is running idle in addition to the
trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to t h is instru c tion manual.
SAFETY W ARNINGS
Cordless Blo er Safety Instructions
Read all safety arnings and
WARNING:
all instructions. F ailure to f ollo w t h e w arnings an d
instructions may result in electric shock, fire and/or
serious injury.
Save all arnings and instruc-
tions for future reference.
Training
Read the instructions carefully. Be familiar
1 .
ith the controls and the correct use of the
blo er.
Never allo children, persons ith reduced
2.
physical, sensory or mental capabilities or
lack of experience and kno ledge or people
unfamiliar ith these instructions to use the
blo er. Local regulations may restrict the age
of the operator.
Never operate the blo er hile people, espe-
3.
cially children, or pets are nearby.
Keep in mind that the operator or user is
4 .
responsible for accidents or hazards occurring
to other people or their property.
-2-100:
2
or less
2
Preparation
Al ays ear substantial foot ear and long
1 .
trousers hile operating the blo er.
Do not ear loose clothing or je ellery that
2.
can be dra n into the air inlet. Keep long hair
a ay from the air inlets.
Al ays ear protective goggles to protect
3.
your eyes from injury hen using po er tools.
The goggles must comply ith ANSI
the USA, EN 166 in Europe, or AS/N S 1336
in Australia/Ne
ealand, it is legally re uired to ear a face
shield to protect your face, too.
It is an employer s responsibility to enforce
the use of appropriate safety protective e uip-
ments by the tool operators and by other per-
sons in the immediate orking area.
To prevent dust irritation the earing of a face
4 .
mask is recommended.
While operating the machine, al ays ear
5 .
non-slip and protective foot ear. Non-ski d ,
closed-toed safety boots and shoes will reduce the
risk of injury.
Operation
S itch off the blo er and remove the battery
1 .
cartridge and make sure that all moving parts
have come to a complete stop
henever you leave the blo er.
•
before clearing blockages.
•
before checking, cleaning or orking on
•
the blo er.
if the blo er starts to vibrate abnormally.
•
Operate the blo er only in daylight or in good
2.
artificial light.
Do not overreach and keep proper balance and
3.
footing at all times.
Al ays be sure of your footing on slopes.
4 .
Walk, never run.
5 .
Keep all cooling air inlets clear of debris.
6 .
. Never blo debris in the direction of
bystanders.
Operate the blo er in a recommended position
8 .
and on a firm surface.
. Do not operate the blo er at high places.
1 0. Never point the nozzle at anyone in the vicinity
hen using the blo er.
5 ENGLISH
7.1 in
ealand. In Australia/Ne