Makita DHR280 Betriebsanleitung Seite 16

Rotation only
For drilling in wood, metal or plastic materials, rotate
the action mode changing knob to the
twist drill bit or wood drill bit.
► Fig.10: 1. Rotation only
Hammering only
For chipping, scaling or demolition operations, rotate
the action mode changing knob to the
bull point, cold chisel, scaling chisel, etc.
► Fig.11: 1. Hammering only
Hook
CAUTION:
Never hook the tool at high loca-
tion or on potentially unstable surface.
► Fig.12: 1. Hook
The hook is convenient for temporarily hanging the tool.
To use the hook, simply lift up hook until it snaps into
the open position. When not in use, always lower hook
until it snaps into the closed position.
Adjusting the nozzle position of the
dust collection system
Optional accessory
Push in the guide while pushing up the guide adjustment
button, and then release the button at the desired position.
► Fig.13: 1. Guide 2. Guide adjustment button
NOTE: Before adjusting the nozzle position, release
the nozzle forward completely by pushing up the
guide adjustment button.
If a long drill bit is installed, extend the guide by pushing
up the extension button.
► Fig.14: 1. Extension button
Adjusting the drilling depth of the
dust collection system
Optional accessory
Slide the depth adjustment button to the desired posi-
tion while pushing it up. The distance (A) is the drilling
depth.
► Fig.15: 1. Depth adjustment button
Torque limiter
NOTICE:
As soon as the torque limiter actuates,
switch off the tool immediately. This will help pre-
vent premature wear of the tool.
NOTICE:
Drill bits such as hole saw, which tend
to pinch or catch easily in the hole, are not appro-
priate for this tool. This is because they will cause
the torque limiter to actuate too frequently.
The torque limiter will actuate when a certain torque
level is reached. The motor will disengage from the
output shaft. When this happens, the drill bit will stop
turning.
Electronic function
The tool is equipped with the electronic functions for
symbol. Use a
easy operation.
•
•
symbol. Use a
NOTE: This function does not work if the acceleration
does not reach the predetermined one when the tool
is swung.
NOTE: If the bit is swung at the predetermined
acceleration during chipping, scaling, or demolishing,
the motor is forcibly stopped. In this case, release
the switch trigger, and then pull the switch trigger to
restart the tool.
ASSEMBLY
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Side grip (auxiliary handle)
safe operation.
side grip, make sure that the side grip is firmly
secured.
To install the side grip, follow the steps below.
1.
► Fig.16: 1. Thumb screw
2.
screw so that the grooves on the grip fit in the protru-
sions on the tool barrel.
► Fig.17: 1. Thumb screw
3.
grip can be fixed at desired angle.
Grease
Coat the shank end of the drill bit beforehand with a
small amount of grease (about 0.5 - 1 g).
This chuck lubrication assures smooth action and lon-
ger service life.
Installing or removing drill bit
Clean the shank end of the drill bit and apply grease
before installing the drill bit.
► Fig.18: 1. Shank end 2. Grease
16 ENGLISH
Constant speed control
The speed control function provides the constant
rotation speed regardless of load conditions.
Active Feedback sensing Technology (For
DHR282/DHR283)
If the tool is swung at the predetermined accelera-
tion during operation, the motor is forcibly stopped
to reduce the burden on the wrist.
CAUTION:
Always be sure that the tool is
CAUTION:
Always use the side grip to ensure
CAUTION:
After installing or adjusting the
Loosen the thumb screw on the side grip.
Attach the side grip while pressing the thumb
Tighten the thumb screw to secure the grip. The