Residual Risks - Ryobi Rmt1801 Originalanleitung

Safety, performance, and dependability have been given
top priority in the design of your cordless multi-tool.
INTENDED USE
The product is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions.
You may use this product for cutting and sanding purposes.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
MULTI-TOOL SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
Protect your lungs. Wear a face or dust mask if the
operation is dusty.
Always wear safety goggles and a dust mask when
sanding, especially sanding overhead.
A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air.
The dust produced when using the product may be
harmful to the health of the operator and bystanders.
Operator and bystanders shall not touch and not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Clamp workpiece with
Unclamped workpieces can cause severe injury and
damage. Do not hold the material you are sanding by
hand.
Do not use sanding paper larger than needed. Extra
paper extending beyond the sanding pad can also
cause serious lacerations.
Ambient temperature range for tool during operation is
between 0°C and 40°C.
Ambient temperature range for tool storage is between
0°C and 40°C.
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
a clamping device.
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
Ambient temperature range for battery during use is
between 0°C and 40°C.
Ambient temperature range for battery storage is
between 0°C and 20°C.

RESIDUAL RISKS

Injury caused by dust
–
Wear eye protection at all times.
– Wear respiratory protection masks containing filters
appropriate to the materials being worked. Ensure
adequate workplace ventilation.
–
Do not eat, drink or smoke in the work area.
Injury caused by noise and vibration
– Wear ear protection.
–
Do not operate the product for long periods of time.
See "Risk reduction".
Risk of electrocution if electric cables are cut
–
Always hold the product by designated handles. Do
not touch the cutting blades or metal parts of the
product.
RISK REDUCTION
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
1