Dust/Chip Extraction; Starting Operation - Bosch GGS 18V-23 LC Professional Originalbetriebsanleitung

18 | English
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Fitting the Abrasive Tools (see figure A)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Only use open-ended spanners that are suitable and
u
undamaged (see "Technical Data").
– Clean the grinding spindle (3) and all the parts to be fit-
ted.
– Use an open-ended spanner (10) on the spanner flat of
the grinder spindle (3) to hold it in place.
Loosen the clamping nut (2) by placing an open-ended
spanner (11) on the spanner flat and turning it counter-
clockwise.
– Insert the straight shank of the grinding tool all the way
into the collet (1).
– Hold the grinding spindle (3) with the open-ended span-
ner (10) and tighten the application tool by placing the
open-ended spanner (11) on the spanner flat and turning
it clockwise.
The grinding tools must run completely concentrically. Do
not continue to use damaged grinding tools that are out of
balance. If the grinding tools are out of balance, they should
be replaced.
Do not, under any circumstances, tighten the collet
u
with the clamping nut until a grinding tool has been
fitted. The collet may otherwise become damaged.
Only use mounted points with an appropriate shank
u
diameter. A mounting point with a shank diameter which
does not correspond to the tool holder of the power tool
(see "Technical data") cannot be held properly and will
damage the collet chuck.
The application tool must be clamped at least 10 mm.
u
The inner shank dimension L
0
maximum permitted speed of the application tool from
the specifications provided by the manufacturer of the
application tool. It must not be less than the maximum
speed of the power tool.
1 609 92A 5DG | (15.10.2019)
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
can be used to calculate the

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation

Starting operation

Switching On/Off (GGS 18V-23 LC)
To start the power tool, push the on/off switch (5) forwards.
To lock the on/off switch (5) in position, push the on/off
switch (5) forwards and down until it clicks into place.
To switch off the power tool, release the on/off switch (5);
or, if the switch is locked, briefly push the on/off switch (5)
backwards and down and then release it.
Switching On/Off (GGS 18V-23 PLC)
To start the power tool, push the unlocking lever (13) for-
wards and then push the on/off switch (5) up.
To switch off the power tool, release the on/off switch (5).
Inserting the Battery
Use only original Bosch lithium-ion batteries with the
u
voltage stated on the type plate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Push the charged battery (7) into the base of the power tool
until the battery is securely locked.
Kickback Stop
If there is a sudden kickback in the power tool,
e.g. jamming when carving, the power supply
to the motor will be interrupted electronically.
To restart the tool, set the on/off switch (5) to
the off position and then switch the power tool on again.
Bosch Power Tools