Installation Conditions - Bwt Infinity A Einbau- Und Bedienungsanleitung

0 0 0
Σ m
3
> 400 mm > 400 mm > 400 mm
> 400 mm > 400 mm
> 20 mm > 20 mm
> 20 mm > 20 mm > 20 mm
> 1 m > 1 m > 1 m > 1 m > 1 m

Installation conditions

Installation conditions
Installation conditions Installation conditions Installation conditions
Observe all applicable installation regulations, gen-
eral guidelines and technical specifications.
There must be a flush of at least 3.5m
backwashing. The pressure downstream of the
filter during backwashing must be at least 2.5 bar.
A connection to the sewage system (min. DN 50) A connection to the sewage system (min. DN A connection to the sewage system (min. DN
A connection to the sewage system (min. DN A connection to the sewage system (min. DN
m m m m m ust be a ust be av v v v v ailab ust be a ust be a ailab ailab le f le f or dr or dr
ust be a ailab ailable f le f le for dr or dr or draining the flushing w
There must be a 230V/50Hz mains socket within There must be a 230V/50Hz mains socket within
There must be a 230V/50Hz mains socket within There must be a 230V/50Hz mains socket within There must be a 230V/50Hz mains socket within
1.2m to pro 1.2m to pro 1.2m to pro 1.2m to pro 1.2m to provide the unit with electr vide the unit with electrical po vide the unit with electr vide the unit with electr vide the unit with electr
The installation site must be protected against frost
and must guarantee the protection of the filter from
solvent vapors, fuel oil, lees, chemicals of all types,
UV irradiation, and heat sources over 40°C.
Note: Keep plastic parts free of oil, grease, sol- Note: Keep plastic parts free of oil, grease, sol- Note: Keep plastic parts free of oil, grease, sol-
Note: Keep plastic parts free of oil, grease, sol- Note: Keep plastic parts free of oil, grease, sol-
vents, and acid or alkaline cleaning agents. vents, and acid or alkaline cleaning agents. vents, and acid or alkaline cleaning agents. vents, and acid or alkaline cleaning agents. vents, and acid or alkaline cleaning agents.
After hard collisions and impacts (e.g. with un- After hard collisions and impacts (e.g. with un-
After hard collisions and impacts (e.g. with un- After hard collisions and impacts (e.g. with un- After hard collisions and impacts (e.g. with un-
suitable tools suitab suitab suitab suitab le tools le tools, f , f , f , f , falls onto stone floor le tools le tools alls onto stone floor alls onto stone floor alls onto stone floor, etc.) a plastic alls onto stone floor
part must be replaced, even if there is no visible part must be replaced, even if there is no visible
part must be replaced, even if there is no visible part must be replaced, even if there is no visible part must be replaced, even if there is no visible
damage (danger of bursting). Avoid extreme damage (danger of bursting). Avoid extreme damage (danger of bursting). Avoid extreme damage (danger of bursting). Avoid extreme damage (danger of bursting). Avoid extreme
pressure blows. pressure blows.
pressure blows. pressure blows. pressure blows.
3
per hour for
50) 50) 50)
50)
aining the flushing w aining the flushing w ater. . . . . ater ater
aining the flushing w aining the flushing water ater
ical pow w w w w er er er er er. . . . . ical po ical po ical po
, etc.) a plastic , etc.) a plastic , etc.) a plastic , etc.) a plastic
GB GB GB GB GB
1 5 1 5 1 5 1 5 1 5