Usb Device Playback; Remote Control - Yamaha TSX-132 Bedienungsanleitung

CD playback
Problem
CD cannot be inserted.
Some button operations do not
work.
Playback does not start
immediately after pressing
(playback stops immediately.).
When you insert a disc, the front
panel display indicates "No Disc"
or "CD Unknown."
The front panel display indicates
"no operation", and a disc cannot
be inserted or unloaded.

USB device playback

Problem
MP3/WMA file on the USB
device does not play.
When you connect a USB device,
the front panel display indicates
"USB OverCurrent," and then
the front panel display goes
blank.
FM reception
Problem
Too much noise.
Too much noise during stereo
broadcast.
Even with an outdoor antenna,
radio wave reception is weak.
(Sound is distorted.)

Remote control

Problem
The remote control does not work
properly.
Cause
Another disc is already inserted.
You are attempting to insert a disc that cannot be
used by this unit.
The disc loaded into the unit may not be
compatible.
The disc may be dirty.
The disc loaded into the unit may not be compatible. Use a disc supported by the unit (☞ P. 18).
If the unit was moved from a cold to warm place,
condensation may have formed on the disc
reading lens.
The disc loaded into the unit may not be
compatible.
The disc may be dirty, or a foreign object may
have adhered to it.
The disc does not contain playable files.
The disc was inserted upside down.
The clock/alarm/tone settings are in progress.
Alternatively, the alarm is playing.
Cause
The USB device is not recognized.
The USB device does not contain playable files.
An incompatible USB device is connected to the
unit. Alternatively, the USB device is not connect
firmly to the unit.
Cause
The antenna may be connected improperly.
The antenna is too close to the unit or to an
electronic device.
The radio station you selected may be far from
your area, or the radio wave reception is weak in
your area.
Multipath reflection or other radio interferences
may have occurred.
Cause
The remote control may be operated outside its
operation range.
The remote control signal receiver on the unit
(☞ P. 3) may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
The battery may be worn out.
There are obstacles between the remote control
signal receiver on the unit (☞ P. 3) and the
remote control.
Solution
Unload the disc with EJECT.
Use a disc supported by the unit (☞ P. 18).
Use a disc supported by the unit (☞ P. 18).
Wipe the disc clean.
Wait for an hour or two until the unit adjusts to the room
temperature, and try again.
Use a disc supported by the unit (☞ P. 18).
Wipe the disc clean. Alternatively, remove any foreign
object that has adhered to the disc.
Use a disc containing playable files (☞ P. 18).
Insert the disc with the label facing upward.
Complete the clock/alarm/tone settings. Alternatively, stop
the alarm.
Solution
Turn the system off and disconnect the USB device.
Then turn the system on and reconnect the USB device to
the unit.
If the solutions above do not resolve the problem, the USB
device is not playable on the unit (☞ P. 18).
Use a USB device contains playable files (☞ P. 18).
Turn the system off and disconnect the USB device.
Then turn the system on and reconnect the USB device to
the unit.
If the solutions above do not resolve the problem, the USB
device is not playable on the unit (☞ P. 18).
Solution
Make sure the antenna is connected properly (☞ P. 3) or
use a commercially available outdoor antenna.
Position the antenna as far away as possible from the unit
or the electronic device.
Try manual tuning to improve the signal quality (☞ P. 9) or
use a commercially available outdoor antenna.
Change the height, direction, or placement of the antenna.
Solution
For information on the remote control operation range,
refer to "How to use the remote control" (P. 1).
Change the lighting or orientation of the unit.
Replace the battery with new one (☞ P. 1).
Remove the obstacles.
TROUBLESHOOTING
17
En