Error Messages; Specifications - Yamaha DG100-212 Bedienungsanleitung

Error Messages

If an error occurs during operation, one of the following error message numbers will appear on the display.
E1
: Motor Drive Error
CAUSE: The volume knob has not returned to its assigned position after 20 seconds has elapsed from the start of the recall operation or, the device
does not recognize the recall command.
SOLUTION: Turn off the power and return the device to the music dealer where you purchased it, or to the nearest Yamaha Service Center for repair.
E2
: MIDI Receive Buffer Full
CAUSE: Too much MIDI data is being received by the DG100-212 at one time.
SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks.
E3
: Communication Error.
CAUSE: An abnormality is detected during MIDI communications.
SOLUTION: Check all connections, etc. and try again.
E4
: Bulk Receive Check Sum Error.
CAUSE: The check sum does not match the received MIDI bulk data.
SOLUTION: Check all connections and data, and try again.
E5
: Bulk Receive Data Abnormality.
CAUSE: An abnormality is detected in the received MIDI bulk data.
SOLUTION: Check all connections and data, and try again.
E6
: Backup Battery Error.
CAUSE: Backup battery power is depleted.
SOLUTION: Continued use of the device will result in the loss of data. Return the device to the music dealer where you purchased it or, the nearest
Yamaha Service center and have the battery replaced.

Specifications

Digital Section
Complete Digital Signal Processing
Internal 8 Channel Preset
Digital Reverb (SPRING, HALL, PLATE)
Digital Tape Echo
Speaker Simulator (LINE OUT)
Analog Section
100W Solid State Power Amp
30 cm Speaker (Celestion Vintage 30) x 2
MIDI Function
Receive : Program change, Control Change (No. 7, 91, 94), Bulk In
Transmit : Bulk Out, Merge Out
Controller/Switch
Front Panel : TRIM, OUTPUT, GAIN, MASTER, TREBLE, HIGH
MID, LOW MID, BASS (TIME), PRESENCE (FEED BACK),
REVERB (LEVEL)
Rear Panel : LINE OUT volume, EFFECT BLEND
Switch : AMP SELECT (LEAD1, LEAD2, DRIVE1, DRIVE2,
CRUNCH1, CRUNCH2, CLEAN1, CLEAN2), REVERB,
MODE, , , STORE, RECALL
Display
AMP SELECT display LED x 8
MODE display LED x 3
REVERB type display x 3
7 segment LED x 2 digits
Indicator
Trim Level Display LED (Green)
Trim Clip Display LED (Red)
12
Connection Jacks
INPUT HIGH/LOW, SPEAKER, EFFECT SEND/RETURN:
Standard Phone Mono Jack
LINE OUT: Cannon Jack
MIDI IN, MIDI OUT: 5 pin DIN
A/D Converter 20 bit
D/A Converter 20 bit
Sampling Frequency 48 kHz
Memory Number 128
Input Level/Impedance
INPUT HIGH: –30dBm (THRU)/1MΩ
INPUT LOW: –20dBm (THRU)/1MΩ
EFFECT RETURN: 0dBm/120kΩ
Output Level/Impedance
SPEAKER: 100W RMS/4Ω
LINE OUT: +4dBm/600Ω
EFFECT SEND: 0dBm/120kΩ
Power Requirements
U.S. and Canadian models : 120V, 60Hz
General model : 230V, 50Hz
Power Consumption 100W
Dimensions (w/Caster) 712 (W) x 574 (H) x 284 (D) mm
28" (W) x 22.6" (H) x 11.2" (D)
Weight 33.5 kg (73 lbs 13 oz)
* Specifications and design may change without notice.