Important Remarks; Installation; Limit Switch Adjustment - V2 VEO Serie Handbuch

EU DECLARATION OF CONFORMITY AND
DECLARATION OF INCORPORATION FOR
PARTLY COMPLETED MACHINERY
Declaration in accordance with the Directives: 2014/35/UE
(LVD); 2014/30/UE (EMC); 2006/42/EC (MD) APPENDIX II,
PART B
The manufacturer V2 S.p.A., headquarters in
Corso Principi di Piemonte 65, 12035, Racconigi (CN), Italy
Under its sole responsibility hereby declares that:
the partly completed machinery model(s):
• VEO6 (*), VEO10 (*)
• LEX20 (*), LEX30 (*), LEX40 (*), LEX50 (*)
• LEX-H20 (*), LEX-H30 (*), LEX-H40 (*), LEX-H50 (*)
• ROLL80 (*), ROLL100 (*)
• HANDROLL80 (*), HANDROLL100 (*)
Description: electromechanical actuator for awnings and
rolling shutters
- is intended to be installed on awnings and rolling shutters
to create a machine according to the provisions of the
Directive 2006/42/EC. The machinery must not be put into
service until the final machinery into which it has to be
incorporated has been declared in conformity with the
provisions of the Directive 2006/42/EC (annex II-A).
- is compliant with the applicable essential safety requirements
of the following Directives:
Machinery Directive 2006/42/EC (annex I, chapter 1)
Low Voltage Directive 2014/35/EU
Electromagnetic Compatibility Directive 2014/30/EU
Directive ROHS2 2011/65/CE
The relevant technical documentation is available at the national
authorities' request after justifiable request to:
V2 S.p.A., Corso Principi di Piemonte 65,
12035, Racconigi (CN), Italy
The person empowered to draw up the declaration and to provide
the technical documentation:
Giuseppe Pezzetto
Legal representative of V2 S.p.A.
Racconigi, 1st June 2015
(*) made in extra EU Countries on behalf of V2 S.p.A.
m

IMPORTANT REMARKS

• Please read the instruction carefully before installation
• Follow all instructions, since incorrect installation can lead to
severe injury
• The installation must be done by a technician following the
safety norms in force
• Only apply to authorized personnel to replace the feeding
cable of the motor
• Do not pierce nor insert screws in the whole length of the
motor
• Avoid any contact of the motor with liquids
• Avoid to crush or knock over the motor
• Possible tampering or wrong connections are not covered by
guarantee
•
If a manual release is provided, the actuating member is to be
installed at a height less than 1,8m
• Before installing the drive, remove any unnecessary cords and
disable any equipment not needed for powered operation.
• For installation for awnings, a horizontal distance of at least
0,4 m is to be maintained between the fully unrolled driven
part and any permanent object
• The power supply cable should not be exposed to sunlight or
rain directly
• Assure that all accessories have been fixed so that the motor
works without any mechanical problem. The loading weight
should be matched with the output power of the motor
• Electrical connection must be done by professional technicians
to operate in conformity with the rules
• Do not allow children to play with fixed controls
• Keeps remote controls away from children
• Frequently examine the installation for imbalance and sings of
wear or damage to cables and springs
• Do not use if repair or adjustment is necessary
• Moving parts of the drive must be installed higher than 2.5 m
above the floor or other level that could provide access to it
• The actuating member of a biased-off switch is to be located
within direct sight of the driven part but away from moving
parts. It is to be installed at a minimum height of 1.5 m
• Fixed controls have to be installed visibly
• The appliance can not be used in outside

INSTALLATION

• Fix the stirrup G to the wall.
• Insert the crown A in the driving wheel B of the limit switch
(fig.1).
• Insert the pulley C on the pivot of the motor D (fig.1).
• Insert the copper pin F on the pulley C.
• ONLY for the models with emergency handling:
- Put the eyelet L in the hole
- Fix the eyelet with the screw M and the washer N
• Insert completely the motor in the roll-tube (fig.2).
• Fix the roll-tube to the driving wheel with m 4 x10 screw
(fig.2).
ELECTRIC CONNECTIONS
• Operators must be installed with a bipolar switch with a
minimum contact clearance opening distance of at least 3mm
(fig.3).
• Do not connect more than one motor for every push-button
of command.
• Reverse the brown and black cables, in order to change the
direction of revolution (fig.3)

LIMIT SWITCH ADJUSTMENT

• The limit switches system is electromechanical and through a
micro-switch it interrupts the feeding of the motor when the
roller shutter or the awning reaches the limit of opening and
closing.
• The limit switches are pre-adjusted to approximately 5 crown
revolutions.
• To adjust the opening and closing limit is necessary to turn the
adjusting screw placed on the head of the motor through the
plastic screwdriver included in the box (fig.4).
• Feed the motor and observe the sense of rotation of the pulley
and/or of the crown ; turn the adjusting screw towards (+)
to increa se the speed of the motor, turn the adjusting screw
towards (-) to decrease it (fig.4).
• Reverse the direction of revolution of the motor and operate
on the second limit switch (fig.4).
- 7 -