RECARO Sport Reha Handbuch Seite 6

Footrest adapter (accessory)
Before assembly, clean the plastic surface on the underside of the seat with commercially available cleaning agents (e.g. water and rinsing agent) until it is completely
free from grease.
Now remove the Velcro strips (fleece) from the adapter plate and attach them to the underside of the seat. The Velcro strips (hooks) remain on the adapter plate.
Position the seat flush in a 90° angle at the front of the adapter (handle of the adapter facing forwards) and tilt the seat over to velcro it to the adapter.
Footrest: The footrest is attached to the adapter.
Fig. 1: Attaching Velcro straps to the seat
Footrest, short 12 cm / 4.7" (accessory)
Press the catch springs in at the rear ends of the sliding rods and push the tubes into the holes as far as they will go.
To stabilize the footrest on the vehicle floor adjust the height of the support bars by screwing them in or out until they have contact with the vehicle. Then lock the
support bars with the hand knobs to prevent them unscrewing accidentally. Screw the hand knobs upwards as far as possible and tighten them fast.
Lower leg length:
The lower leg length is adjusted by changing the height of the footrest. Loosen both outer knurled nuts. Retighten them after each adjustment. To achieve the highest
position possible, use the elevation block (+10 cm / 3.9") provided. It is attached centrically on the footrest by Velcro.
Foot angle:
Loosen the four screws left and right on the underside of the footrest to adjust the desired foot angle with the rails. Then retighten the screws.
Note:
Always secure the footrest against falling off with the hand knob provided with the user manual. The receiver for the hand knob (metal block with thread) is situated on
the left tube of the footrest adapter.
Fig. 1: Inserting the support
Turning plate with footrest adapter (accessory)
Before assembly, clean the plastic surface on the underside of the seat with commercially available cleaning agents (e.g. water and rinsing agent) until it is completely
free from grease.
Now remove the Velcro strips (fleece) from the turning plate and attach them to the underside of the seat. The Velcro strips (hooks) remain on the turning plate.
Position the seat flush in a 90° angle at the front of the turning plate (handle of the turning plate facing forwards) and tilt the seat over to velcro it to the turning plate.
The turning plate is pre-assembled for the attachment of the car seat on the right back seat of the vehicle (safe placing / removing of the child from the sideway in
countries with right hand traffic). If the car seat shall be fixed to the left back seat the pivotal point of the turning plate has to be changed. This is done by simply
dislocating the Allen screw from right to left.
Note:
The audible clicking into place of the turning plate just serves as orientation aid for the straight positioning of the seat on the turning plate.
Transport:
To transport the seat with turning plate, hold the handle of the turning plate with one hand and the back of the seat with the other. To reduce the load, seat and turning
plate can also be transported separately.
Footrest:
The footrest is attached to the bottom part of the turning plate with the adapter.
Fig. 1: Attaching Velcro straps to the seat
Seat wedge, bottom (accessory)
The seat wedge is positioned centrically below the car seat. The high edge is at the front to achieve an optimum rest position of the child.
The cover can be removed (zipper) and washed in the machine at up to
30° C / 86° F.
Please note:
Function of the turning plate is considerably reduced if being used in combination with the seat wedge. We therefore do not recommend using seat wedge and turning
plate at the same time.
Fig. 1: Positioning seat on seat wedge
Table (accessory)
Mount the side parts of the table first, by pulling them over the round corners of the seat. The side with the larger fabric must face outwards. Attach the fabric to the
wheels for the seat adjustment using the provided holes in the cover of the side parts. Then tuck the downwards overlaying fabric below the seat cover.
Now fasten the table to the Velcro straps of the side parts.
Note:
For reasons of space the crotch pad should be removed when using the table.
The cover can be removed and washed in the machine at up to 30° C / 86° F.
Fig. 1: Mounting the side parts
6
RECARO Sport Reha – Instructions for assembly and use of the Reha version
Fig. 2: Attaching seat to adapter
Fig. 2: Adjusting height to vehicle
Fig. 2: Attaching seat to turning plate / dislocating the Allen screw
Fig. 2: Final position
Fig. 2: Attaching the table
item code: 866
item code: 806
item code: 812
item code: 810
item code: 811