After-Sales Service And Application Service - Bosch UniversalChain series Originalbetriebsanleitung

22 | English
Check that covers and guards are undamaged and correctly
fitted. Carry out necessary maintenance or repairs before
using.
Note: Before returning the chain saw, ensure all oil in the oil
reservoir has been emptied. Ensure that the oil reservoir is
refilled before using the chain saw again.
Replacing the Saw Chain and Chain Bar
Check the saw chain and chain bar according to section
"Tensioning the Saw Chain".
Replace a worn chain bar.
Check the drive sprocket (19). If it is worn out or damaged
due to strain, have it exchanged by an authorized Bosch
after-sales service.
Sharpening the Saw Chain
Never sharpen the saw chain yourself unless you have exper-
ience with it. Replace the saw chain with the Bosch spare
saw chain or have the saw chain professionally resharpened
at an authorised customer services agent for Bosch power
tools.
Checking the Automatic Oiler (see figure C2)
Proper functioning of the automatic saw chain oiler can be
checked by running the chain saw and pointing the tip of the
chain bar towards a piece of cardboard or paper on the
ground. Do not touch the ground with the chain and ensure a
safety clearance of 20 cm. If an increasing oil pattern de-
velopes, the automatic oiler is operating fine. If there is no oil
pattern despite a full oil reservoir, see section
"Troubleshooting" or contact your authorized Bosch after-
sales service.
After Use/Storage
Put the chain guard (7) on the bar (9) to prevent injury.
The saw chain (8) can become blunt because of unwanted
hits/scratches.
Remove the oil from the oil tank before storage.
Clean the moulded plastic housing of the chain saw using a
soft brush and clean cloth. Do not use water, solvents or pol-
ishes. Remove all debris, especially from the motor cooling
vents.
After 1–3 hours of use, remove the cover (13), the chain bar
(9) and the saw chain (8), and clean them using a brush.
Clean the area under the cover (13), the drive sprocket (19)
and the chain bar assembly from adherant debris using a
brush. Clean the oil outlet (22) with a clean cloth.
Note: Do not clean the area around the oil outlet (22) with a
brush, as debris can be lodged into the automatic oiling sys-
tem and can cause blockages and lubrication problems.
Make sure that sawdust and dirt are removed and that the oil
lines and the oil system can not be clogged up.
If the chain saw is to be stored for a longer period of time,
clean the saw chain (8) and the chain bar (9).
Store the chain saw in a secure, dry place, out of the reach of
children.
F 016 L81 829 | (31.10.2019)
Do not place other objects on the chain saw.
Do not modify this product. Unauthorized modifications
may impair the safety of your product and may result in in-
creased noise and vibration.
After-sales Service and Application
Service
www.bosch-garden.com
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
Bosch Power Tools