After-Sales Service And Application Service; Français; Consignes De Sécurité; Explication Des Symboles - Bosch UniversalChain 35 Originalbetriebsanleitung

– Clean the chain and chain bar before storing the product
for an extended period of time to prevent the parts from
seizing.
– Remove the SDS cover (25), chain bar (17) and saw
chain (18) and clean these parts with a brush to remove
oil, sap and dust residue, especially from the saw blade
groove.
– Use a clean cloth to carefully remove debris from the oil
outlet (7) and drive sprocket (3). Make sure that no
debris enters the oil outlet (7), as this can cause block-
ages and lubrication problems.
– Carry out the required maintenance before use.
– Regularly check the chain saw for obvious defects such as
loose, dislodged or damaged saw chain and chain bar,
loose fixings and worn or damaged components.
– Do not modify this product. Unauthorized modifications
may impair the safety of your product and may result in
increased noise and vibration.
– Always empty the oil reservoir before storage and refill it
before use.
– Store the chain saw in a secure, dry place, out of the
reach of children.
– Do not place other objects on the chain saw.
Replacing and Sharpening the Saw Chain
– The saw chain can become blunt through prolonged use
or when coming into contact with objects other than
wood.
– A sharp saw chain is required for optimum performance
and safety.
– Never sharpen the saw chain yourself unless you have ex-
perience with it.
– Replace the saw chain with the Bosch saw chain access-
ory or have the saw chain professionally resharpened.
Replacing the Chain Bar
Only replace the chain bar if you fully understand the
u
product and the instructions, otherwise please con-
tact the Bosch Service Centre.
– If the chain bar is worn, you can mount it upside down to
extend its life, or you can replace it.
– Use a hex key to loosen the screw between the chain
bar (17) and the affixed tensioning wheel (19).
– Once you have flipped or replaced the chain bar, reattach
the affixed tensioning wheel (19).
Note: Tighten by hand until slight resistance, then add 1/8
extra turn for the required fixing. Overtightening can cause
the chain bar to pinch and restrict the path of the rotating
saw chain.
Chain Bar
UniversalChain 35
UniversalChain 40

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
Bosch Power Tools
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
The product, accessories and packaging should be sorted
for environmental-friendly recycling.
Only for EU countries:
According to the European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment and its implementation
into national law, power tools that are no longer usable must
be collected separately and disposed of in an environment-
ally friendly manner.
Only for United Kingdom
According to Waste Electrical and Electronic Equipment Reg-
ulations 2013 (2013/3113) (as amended), power tools
that are no longer usable must be collected separately and
disposed of in an environmentally friendly manner.
Français
Consignes de sécurité

Explication des symboles

Oregon 144MLEA041
Oregon 164MLEA041
Do not dispose of products into household
waste!
Lire soigneusement ces instructions d'utilisa-
tion.
F 016 L94 197 | (17.11.2021)
Français | 19