Husqvarna LC 141iV Bedienungsanweisung Seite 19

2. Move the lower knobs up in the direction of the
handle until they stop and you hear a click. (Fig. 35)
3. Tighten the knobs.
4. Lift the upper handle and tighten the knobs. (Fig. 41)
To set the cutting height
1. Move the cutting height lever rearward to increase
the cutting height.
2. Move the cutting height lever forward to decrease
the cutting height. (Fig. 42)
CAUTION: Do not set the cutting height too
low. The blades can hit the ground if the
surface of the lawn is not level.
Battery
WARNING: Before you use the battery, you
must read and understand the safety
chapter. You must also read and understand
the operator's manual for the battery and the
battery charger.
Battery status
The display shows the remaining battery capacity and if
there are problems with the battery. The battery capacity
is shown for 5 seconds after the product is switched off
or the battery indicator button is pressed. The warning
symbol on the battery is on when an error has occurred.
Battery on page 22 .
See
(Fig. 43)
LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note: The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature is
above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
919 - 003 - 23.10.2019
Battery status
Fully charged (75-100%)
The battery is 50%-75%
charged
The battery is 25%-50%
charged
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 44)
3. Put the battery in the battery charger. The green light
on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 45)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To operate LC 141iV and LC 141i
To start the product
1. Put a charged battery in the battery compartment.
2. Turn the safety key to 1. (Fig. 27)
3. Stay behind the product.
4. Press the ON/OFF button (A) on the control panel
and the green LED (B) comes on. (Fig. 46)
5. Loosen the start inhibitor. (Fig. 47)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 48)
To use the drive on the wheels
• Model LC 141iV. Pull the drive bail in the direction of
the handlebar to start the drive. (Fig. 49)
• Press + and - on the control panel to set the drive
speed in 4 steps. (Fig. 50)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
Charging status
0%-25%
50%-75%
75%-100%
Fully charged
19