Ingersoll-Rand 1R Serie Technische Produktdaten Seite 4

EN
Model(s) Style
1RPLC3 Reversible In-Line Push Throttle
1RPMC1 Reversible In-Line Push Throttle
1RPMC3 Reversible In-Line Push Throttle
1RPNC1 Reversible In-Line Push Throttle
1RPNC3 Reversible In-Line Push Throttle
1RPMC9D Reversible In-Line Push Throttle
1RPNC9D Reversible In-Line Push Throttle
1RPLS1 Reversible In-Line Push Throttle
1RPLS3 Reversible In-Line Push Throttle
1RPMS1 Reversible In-Line Push Throttle
1RPMS3 Reversible In-Line Push Throttle
1RPNS1 Reversible In-Line Push Throttle
1RPNS3 Reversible In-Line Push Throttle
1RPQS1 Reversible In-Line Push Throttle
1RPQS3 Reversible In-Line Push Throttle
† K = 3dB measurement uncertainty
pA
Sound and vibration values were measured in compliance with internationally recognized test standards. The exposure to the user in
a specific tool application may vary from these results. Therefore, on site measurements should be used to determine the hazard level
in that specific application.
Installation and Lubrication
Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping,
air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose
coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 16585770 and table on
page 2. Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days, and m=months of actual use. Items identified as:
1. Air filter
2. Regulator
3. Lubricator
4. Emergency shut-off valve
Clutch Adjustment
Turn off the air supply and disconnect the air supply hose from the Tool before proceeding.
1. Rotate the Adjusting Hole Cover on the Clutch Housing to expose the adjusting hole.
2. Insert a 1/4" hex wrench into the Bit Holder. Rotate the clutch mechanism until one of the radial holes in the Clutch Adjusting Nut is visible
through the adjusting hole. Insert the No. 5C1-116 adjusting key or a 3/32" (2 mm) diameter hardened steel pin or rod into the hole in the
adjusting nut to sprag the Nut against rotation.
3. Grasp the Tool firmly in one hand and rotate the Bit Holder to shift the Adjusting Nut along the Bit Holder. Rotating the Bit Holder clockwise
facing the front increases the compression on the Clutch Spring and raises the torque at which the clutch will ratchet or shut the Tool off.
The most satisfactory adjustment is usually obtained by using the tool on the actual application and increasing or decreasing the
delivered torque until the desired setting is reached. In any event, it is recommended that final adjustment be made by gradual
progression.
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that
they can be recycled.
Original instructions are in English. Other languages are a translation of the original instructions.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest Ingersoll Rand Office or Distributor.
EN-2
Clutch Type
Adjustible Cushion
Adjustible Cushion
Adjustible Cushion
Adjustible Cushion
Adjustible Cushion
Adjustible Cushion
Adjustible Cushion
Shut-off Clutch
Shut-off Clutch
Shut-off Clutch
Shut-off Clutch
Shut-off Clutch
Shut-off Clutch
Shut-off Clutch
Shut-off Clutch
WARNING
5. Hose diameter
6. Thread size
7. Coupling
8. Safety Air Fuse
WARNING
NOTICE
Recommended Sound Level dB(A)
Torque Range
in-lbs (Nm)
3.5 - 13 (0.39 - 1.5)
2.5 - 20 (0.28 - 2.3)
2.5 - 20 (0.28 - 2.3)
1.5 - 30 (0.17 - 3.4)
1.5 - 30 (0.17 - 3.4)
2.5 - 20 (0.28 - 2.3)
1.5 - 30 (0.17 - 3.4)
3.5 - 13 (0.39 - 1.5)
3.5 - 13 (0.39 - 1.5)
2.5 - 20 (0.28 - 2.3)
2.5 - 20 (0.28 - 2.3)
1.5 - 30 (0.17 - 3.4)
1.5 - 30 (0.17 - 3.4)
1.5 - 45 (0.17 - 5.1)
1.5 - 45 (0.17 - 5.1)
9. Oil
10. Grease (disassembly required, see maintenance instructions)
11. Grease (disassembly required, see maintenance instructions)
Vibration Level
(ISO15744) (ISO28927)
† Pressure (L ) m/s
2
p
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
73.7 < 2.5
80167265_ed3