Extra Facilities - Philips Suncare Bedienungsanleitung

Remote control unit (HB828 only) (fig.1)
a
- Time setting button for 1-30 minutes.
b
- Start button: press this button to switch on the tanning lamps and the timer.
c
- Pause/repeat button: press this button if you want to interrupt the session (e.g. when the telephone rings).The tanning lamps will go out
and the remaining time of the session will blink in the display.You can also press this button during the last minute of a session to repeat the
set time (e.g. to treat the other side of your body).
d
- Blinking signal: this signal is only visible when the timer is counting down the time.
e
- Pilot light: this light is on when the appliance is connected to the mains.
f
- Beeper: the beeper indicates that the last minute of the time set for the tanning session has started.
- If you want the tanning appliance to operate longer than the set time, you will have to set a new time when you hear the beeper go off.You
can also press button T during the last minute of a session to repeat the set time.
g
- Display: the display shows the set time. During the session the display shows the remaining time.
ATTENTION
B
The following illustrations show which button to press.
In the following cases you will see 00 in the display:
- after you have inserted the plug into the wall socket;
- at the end of the tanning session (blinking during the first three minutes);
- after a mains failure;
- after the overheat protection has come into operation.
In these cases the tanning lamps will not be on.
1 Fully unwind the mains cord and take the remote control unit out of the storage compartment.
2 Insert the mains plug into the wall socket.
3 Consult the memory knobs and the table in these instructions for use.
4 Put on the protective goggles supplied.
5 Set the duration of the tanning session (fig. 13).
Press + to put the time forward.
Press - to put the time backward.
Keep the button pressed to adjust the time more quickly.
6 Switch on the tanning lamps (fig. 14).
Press button I. Blinking signal d will become visible on the display and the preset session time will be shown.
The timer will count down the set session time.
During the last minute of the session, the beeper f will sound.
During this minute you can press button T to repeat the session time or set a new time.
By doing this, you can avoid the 3-minute waiting time which is necessary to allow the tanning lamps to cool down after they have been
switched off.
7 Lie down under the lamp unit.
Repeating the session time (during the last minute) (fig. 15).
Press button fi.The previously set tanning session time appears on the display.The beeping stops.
Setting a different session time (during the last minute) (fig. 16).
Set a new tanning session time and then press button I.
As soon as this button has been pressed, the beeping will stop and the new session time will start.
If you do not repeat the session time or set a new session time, the tanning appliance will switch off automatically as soon as the set
session time has elapsed.

Extra facilities

Interruption of the tanning session (e.g. to answer a telephone call) (fig. 17).
Press button fi
-
The tanning lamps are switched off. Blinking signal d disappears from the display.
The remaining tanning session time blinks on the display.
- After three minutes, the blinking stops.Then you can switch on the tanning lamps again by pressing button I.
If you want to use the tanning appliance shorter than the set time: (fig. 18).
press button I.The tanning lamps are switched off and you can set a new session time;
-
wait until the time shown on the display stops blinking.Then press button I again.
-
After the tanning session
Keep track of the number of sessions you have had by means of the memory knobs.The appliance has two memory knobs: one for each
person.
Let the appliance cool down for 15 minutes before you put it in transport position and store it.
ENGLISH
7