Inhaltsverzeichnis
Werbung
EN
NOTICE:
When using as Universal category (group 0+1,2,3), please notice below information:
This is a Universal child restraint. It is approved to Regulation No 44, 04 series of
amendments, for general use in vehicles and it will fit most, but not all, car seats.
A correct fit is likely if the vehicle manufacture has declared in the vehicle handbook that
the vehicle is capable of accepting a Universal child restrain for this age group.
This child restraint has been classified as Universal under more stringent conditions than
those which applied to earlier designs which do not carry this notice.
If in doubt, consult either the child restraint manufacturer or the retailer.
Only suitable if the approved vehicle are fitted with lap/3 point/static/with retractor
safety-belt, approved to UN-ECE Regulation No 16 or other equivalent standards.
Notice regarding IZOFIX child restraint system (in Group 0+)
1.This is an IZOFIX CHILD RESTRAINT SYSTEM. It is approved to Regulation No 44, 04 series
of amendments, for general use in vehicles fitted with IZOFIX anchorages system.
2.It will fit vehicles with positions approved as IZOFIX positions (as detailed in the
vehiclehandbook ), depending on the category of the child seat and of the fixture.
3. The mass group and the IZOFIX size class for which this device is intended is: IZOFIX size
class E for Group 0+ in rearward facing.
When using as Semi-universal category (Group 0+, 1), Please notice below information:
This child restraint is classified for (Restricted/Semi-universal) use and is suitable for
fixing into the seat positions of the following cars:
Seat positions in other cars may also be suitable to accept this child restraint. Please refer
to the information documents or the retailer`s website for the suitable car model list. If in
doubt, consult either the child restraint manufacturer or the retailer any time.
Car Seat Parts
1
1.
Belt guidance
2.
Seat cover
3.
Shoulder pad
4.
Shoulder belt
5.
Buckle latch
6.
Red button
7.
buckle
8.
Crotch pad
9.
Sleeping pad
2
1.
Blue guidance
2.
Connector
3.
Top tether
4.
Metal link
5.
Top tether adjuster
6.
ISOFIX locking arms
7.
ISOFIX button
8.
ISOFIX attachment point
9.
ISOFIX insert guide
20
10. Press button
11. Crotch belt
12. 360 rotate button
13. Base
14. Recline handle
15. Red belt guidance
16. Headrest
17. Headrest height adjuster
To re-fit the cover, simply follow the above steps in reverse.
CAUTION! Never use the child seat without a correctly installed buckle. Make sure that the metal plate is
correctly attached.
CAUTION! Check that the harness straps are not twisted and that they have been correctly inserted in the
belt slots of the cover.
ADJUST THE RECLINE ANGLE OF THE SEAT
7
This child safety car seat can be adjusted to 3 positions.
Before fixing a child in the child restraint system, the seat must be set on the recline
position for rear-facing use, lying level, 9-18kg , 15-36kg use second level. Rotation on the
third level then change to lying level. To archieve this, use the recline handle located in
front of the child restraint system between the seat and the base to adjust it to the desired
position.
ADJUST THE ROTATION ANGEL OF THE SEAT
8
Press the rotation button, then rotate the safety car seat to 90 degree.
ACTION: Before every journey, rotation the seat in both clockwise and anticlockwise
direction. To make sure the rotating part is safe.
ADJUST THE LENGTH OF THE HERNESS
9
To ensure your child`s safety, after fixing him/her in the child restraint system and locking
the buckle, tighten the harness so that it fits snuggle and lies flat against the child`s body. It
should never be twisted or loose.
To tighten the harness, pull the shoulder strap upwards to remove the slack from the lap
sections of the harness and at the same time pull the crotch adjuster belt coming towards
you using your other hand.
To lengthen the harness, press the button on the lock between the child`s legs, then pull
the two shoulders straps simultaneously towards you. While you are doing this, please
make sure you are holding the harness, and not the harness cover.
CAUTION! Check that the harness straps are not twisted and that they have been correctly inserted in
the belt slots of the cover.
ADJUST THE HEIGHT OF THE HARNESS
10
To correctly adjusted harness will ensure that the diagonal seat belt section is optimally
positioned, and will give your child optimal protection.
The harness must be adjusted so that there is a space: two fingers wide between the
harness and your child`s body.
Adjust the height of the harness to fit your child: Loosen the shoulder straps in order to
access the metal link and connector at the back of the child seat.
Remove the straps from connector, then remove the shoulder straps from the metal link,
follow step.
From the front of the child seat, again thread the shoulder straps through the desired slots.
Make sure both of the straps go through the slots at the same height.
Connect both shoulder straps to the connector and metal link again.
23
Werbung
Inhaltsverzeichnis
