Safety Precautions - Vitek Blizzard VT-1836 R Betriebsanweisung

ENGLISH
10. Do not block the inlet or the outlet by any ob-
jects.
Do not turn the appliance on if its inlet or out-
let is blocked. Watch for the filters to be free
from dust, fuzz, hair or other rubbish that
blocks normal air intake.
11. Keep hair, free hanging clothes elements,
fingers and other parts of the body away
from the vacuum cleaner inlet.
12. Always turn the vacuum cleaner off by the
on/off button prior to unplugging it.
13. Be especially careful cleaning the staircase
landings.
14. Do not use the vacuum cleaner to pick up
flammable or combustible liquids (gasoline,
cleaning fluids, perfumes, etc.), or use in ar-
eas where they may be present.
15. Do not pick up burning or smoking ciga-
rettes, matches, or hot ashes, water or other
liquids, as well as fine dust, like plaster, con-
crete, flour or ashes. It may cause serious
electric motor damage and such cases are
not covered by the warranty.
16. Do not use the vacuum cleaner if the: - dust
box container or the container filters are not
installed; - cloth or paper dust box is not in-
stalled.
17. While reeling, secure the power cord with
your hands, do not let the plug hit the floor.
KEEP THE USER MANUAL HANDY

SAFETY PRECAUTIONS

If the intake power of the vacuum cleaner sud-
denly dropped when using, turn the vacuum
cleaner off at once and check the telescopic
extension pipe or the flexible hose for obstruc-
tion. Turn the vacuum cleaner off, then unplug it
– remove the obstruction and only then continue
using it.
• Do not use the vacuum cleaner near heated
surfaces, ashtrays, or in the places where
flammable or combustible liquids may be
present.
• Plug the appliance only with dry hands.
• Prior to usage, pick up sharp objects from the
floor to avoid damaging the filters.
• Never pull the power cord to unplug. Always
take up the plug.
1836.indd 6 1836.indd 6
VACUUM CLEANER ASSEMBLY
Fully unpack the vacuum cleaner and check it for
damages. Before plugging the appliance, make
sure that the power supply voltage corresponds
to the vacuum cleaner operating voltage.
Always turn off and unplug the vacuum cleaner
when servicing it or changing the attachment
brushes.
1. Attaching and removing the flexible hose
(picture 1)
Insert the tip of the flexible hose (4) into the air
inlet, located on the front side of the vacuum
cleaner.
Insert the flexible hose until you hear a click,
confirming the correct attachment.
To remove the flexible hose, press the fixation
button (5) and remove the flexible hose.
2. Attachment of the telescopic extension
pipe and brushes
- Attach the telescopic extension pipe (2) to the
handle of the flexible hose (3) (fig 2). Press
the holder button (fig 3) and extend the lower
part of the telescopic extension pipe to the re-
quired length.
- Choose the required attachment: turbo brush
(1), crevice nozzle (24), furniture upholstery
cleaning brush (25), small brush (26) or floor/
carpet brush (27) and attach it to the tele-
scopic extension pipe (fig 4).
Using of attachments and brushes
Floor/carpet turbo brush (1)
Turbo brush (1) can be used for cleaning of
floors and carpets with long or short pile, ideal
for animal hair removal from carpets. Cylindri-
cal brush with rigid bristle spins in the airflow.
Its bristles effectively "comb" the animal hair out
and "sweeps" the motes from the pile of the car-
pets.
Note: Do not use turbo brush for cleaning of the
carpets with long fringes and the pile over 15
mm to avoid damaging the carpet by the brush
spin. Do not run the turbo brush over power
cords and make sure to turn the vacuum cleaner
right after use.
6
30.08.2007 12:13:29 30.08.2007 12:13:29