Stanley FatMax FMHT77446 Handbuch Seite 14

Performing Accuracy Check
GB
and Calibration
NOTE:
• The laser tool is sealed and calibrated at the factory to the
accuracies specified.
• It is recommended to perform a calibration check before use.
• Be sure to allow the laser tool adequate time to Auto-Level (<
30 seconds) prior to a calibration check.
• The laser tool should be checked regularly to ensure its
accuracies, especially for precise layouts.
Horizontal Check
See Figure Ⓞ
1. Set the laser tool on a tripod 20 m away from a wall with the
"+X" side facing the wall (Figure Ⓞ①).
2.
Power ON the laser tool. Allow the laser tool to Auto-Level
and be sure the laser is rotating.
3. Mark a reference point "D
the wall. If available, use a detector to more easily locate
the beam.
4. Loosen the laser tool from the tripod and rotate the laser
tool 180°. The "-X" side should now be facing the wall
(Figure Ⓞ②). Mark a reference point "D
line appears on the wall.
5.
Measure the vertical distance between reference points "D
and "D " (Figure Ⓞ③).
2
6. If the distance "D
required.
RL 600 & RL 600L
If the distance "D
is necessary.
RL 700L & RL 750L-G
If the distance "D
is necessary.
7.
Rotate the laser 90°. Repeat steps
the Y-axis. Replace "+X" with "+Y" and "-X" with "-Y"
(Figure Ⓞ④).
14
" where the laser line appears on
1
" where the laser
2
" to "D " is < 2.0 mm, calibration is not
1 2
" to "D " is ≥ 3 mm, then calibration
1 2
" to "D " is ≥ 2 mm, then calibration
1 2
1.
through
Horizontal Calibration
See Figure Ⓞ
1.
Rotate the laser to the same position as step
Horizontal Check procedure (with the "+X" side facing the
wall).
2. With laser tool powered OFF, press and hold the
followed by the
3.
Release the
seconds.
4. Release the
5.
The
X-axis Calibration mode.
6. If necessary, adjust the X-axis by using the
key to align the beam with D
between the points D
check (Figure Ⓞ③).
NOTE: Pressing the
by 0.01° (4.4 mm @ 25 m). Figure Ⓜ illustrates how the
arrow keys affect each axis.
7.
Press the
Y-axis adjustment. The
laser tool is in Y-axis Calibration mode.
8. Rotate the laser to the same position as step
Horizontal Check procedure (with the "+Y" side facing the
wall).
"
1
9. If necessary, adjust the Y-axis by using the
key to align the beam with D
between the points D
check.
10.
Press the
Mode.
Axis settings are now saved. Calibration Mode is OFF and
the laser tool begins Auto-Levelling.
11.
Repeat the Horizontal Check procedure to determine if the
calibration was successful.
6.
for
If the laser tool can still not be calibrated after following
the Calibration procedure, send the laser tool into an
Authorized Service Center for repair.
key.
key and continue to hold the
key.
LED flashes GREEN when the laser tool is in
D is the halfway point
0. 0
and D established during the X-axis
1 2
key or the
key again to set the X-axis and proceed to the
LED flashes RED when the
D is the halfway point
0. 0
and D established during the Y-axis
1 2
key again to set the Y-axis and exit Calibration
1.
of the
key
key for ≥ 3
key and the
key slopes the axis
7. of the
key and the