Contents English - Bosch TTM 2104 Originalbetriebsanleitung

en | 30 | TTM 2104 |

Contents English

1. Symbols used
1.1 In the documentation
1.1.1 Warning notices -
Structure and meaning
1.1.2 Symbols in this documentation
1.2 On the product
2. Important notes
2.1 FCC Compliance (USA)
2.2 Electromagnetic compatibility (EMC)
2.3 Applicable documentation
2.4 User group
2.5 Agreement
2.6 Obligation of workshop operator
3. Safety instructions
3.1 Mains voltages
3.2 Danger of tripping
3.3 Eye safety
4. Product description
4.1 Intended use
4.2 Device description
4.3 Scope of delivery
4.4 Spare part, wearing parts and special
accessory
5. Information on
installation location
5.1 General test conditions
5.2 Electrical connection
5.3 Size
5.4 Ground evenness of measuring unit
6. Measurement procedure
6.1 Switching on the TTM 2104
6.2 Calling up the TTM 2104 software
6.3 Crossing specifications
6.4 Measurement of tread depth
6.5 Result of measurement
6.5.1 Display of measurement results
6.5.2 Print-out of measurement results
6.5.3 Process and test protocol
6.6 Browser recommendation
6.7 Switching off TTM 2104
|
1 691 206 005 2017-10-25
31 7. Maintenance
31 7.1 Cleaning
7.1.1 Cleaning intervals
31 7.1.2 Activate maintenance mode
31 7.1.3 Clean measuring units
31 7.1.4 Activating the measurement mode
7.2 Preventive maintenance
31 7.2.1 Service intervals
31 7.2.2 Activate maintenance mode
32 7.2.3 Maintaining measuring units
32 7.2.4 Replacing adsorbers
32 7.2.5 Replacing slide protection strips
32 7.2.6 Activating the measurement mode
32 7.3 Disposal and scrapping
7.4 Faults
33
7.4.1 Faults without fault number
33 7.4.2 Overview of fault numbers
33
33 8. Software configuration
8.1 Starting the system
34
8.2 Settings
34 8.2.1 General information
34 8.2.2 Workshop
34 8.2.3 Thresholds
8.2.4 Device
34 8.2.5 Update
8.3 Display of measurement results
8.4 Process and test protocol
35 8.5 Statistics
35
9. Customer / vehicle data
35
35 9.1 Enter customer and vehicle data
35 9.1.1 Direct data entry
9.1.2 Copying data from orders
36 9.2 Link and transfer customer/vehicle data
36 9.2.1 Link customer/vehicle data with
36 measurement result
36 9.2.2 Canceling the link
37 9.2.3 Transferring data to "Connected
38 Repair"
38 9.2.4 Transferring data to "Entrance Check" 53
38
39 10. Entrance Check / Connected Repair
39 10.1 PC prerequisites
39 10.2 Installation
10.3 Configuration
11. Technical Data
11.1 System data
11.2 Temperature and working environment
11.3 Electrical data
40
40
40
40
40
40
41
41
41
41
42
43
43
44
45
45
46
47
47
47
47
48
48
49
49
50
51
51
52
52
52
52
53
53
53
53
54
54
54
54
55
55
55
55
Robert Bosch GmbH