Inhaltsverzeichnis
Werbung
CAUTION
Check to perform each time Chicco BebèCare easy-tech
is used:
• The smartphone must be turned on and have sufficient
battery charge for the period of use when paired with Chic-
co BebèCare easy-tech.
• Bluetooth® must be active.
• "Airplane" mode must be deactivated.
• GPS must always be active.
Check the Chicco BebèCare APP for sufficient alarm mes-
sages. If this is not the case, proceed with the purchase of
the necessary package.
• If two or more smartphones are used that have the Chicco
BebèCare APP installed, it is necessary to identify which one
is actually connected to the equipment and therefore must
be never abandoned.
• Before each trip, check that the equipment is completely
closed and that the state detected by the Chicco BebèCare
APP is "connected - child seated."
Failure to comply with the above will result in malfunctioning
of Chicco BebèCare easy-tech and/or the Chicco BebèCare
APP and the consequent disabling of the system and/or
failure to send and/or receive alarm messages.
1.1 HOW TO ACTIVATE CHICCO BEBÈCARE EASY-TECH
a) Download the Chicco BebèCare APP
The Chicco BebèCare APP must be downloaded. When accessing
for the first time, the APP will provide all the instructions to follow
to register the account and use Chicco BebèCare easy-tech.
b) Create the family account
A "family account" must be created with a single password. This
account will be the only one that can be used by those who use
that specific equipment. The password is shared with all users who
will interact with the equipment.
IMPORTANT: When creating the family account, an internet con-
nection must be available (mobile data or WiFi network).
IMPORTANT: In the event that the family password is changed,
the new password must be shared with all users who share the
same family account.
c) Enter the emergency numbers
The emergency numbers to which the alarm mes-wise (second
level) containing the data required to geolocate the child must be
entered when accessing for the first time. A minimum of 3 to a
maximum of 5 emergency numbers can be entered. The emer-
gency numbers must be selected from the contacts in your smar-
tphone and can be added, deleted and/or replaced in the future.
IMPORTANT: During this operation, an internet connection must
be available (mobile data or WiFi network).
IMPORTANT: The emergency numbers must be mobile phone
numbers and not landline or national emergency numbers.
IMPORTANT: Always check that the emergency numbers are
correct and are functioning after entering them.
d) Associating the equipment with the family account
To associate your Chicco BebèCare easy-tech equipment with
your family account, carefully follow the instructions in the Chicco
BebèCare App, paying attention to the following.
1) Scan the QR code which is located inside the package
2) At this point you will see the Chicco BebèCare easy-tech logo
and you will need to close the equipment (until the Chicco logo is
completely visible through the window in the white casing) (Fig.1)
to proceed with the first association. To ensure Bluetooth® con-
nection, make sure you are close to your smartphone. The system
activates/connects a few seconds after the device is closed.
Up to a maximum of 3 Chicco BebèCare devices can be associa-
ted with the same family account (child car seats with integrated
sensors and/or anti-abandonment devices). The specific car equi-
pment can be associated with one family account ONLY.
IMPORTANT: When scanning the QR code, an internet con-
nection must be available (mobile data or WiFi network).
e) Check the correct operation of the equipment
When using the first time, to verify the correct operation of Chicco
BebèCare easy-tech, it is important to do some tests, verifying the
relative state of the APP as follows:
- Close the accessory; state detected by the Chicco BebèCare
APP "connected - child seated"
- Then open the accessory: the possible states detected by the
APP are either "connected" or "disconnected" depending on how
long it takes between opening the accessory and displaying it in
the APP.
f) Enter the information about the baby
After associating the equipment with the family account, enter
the name and date of birth of the child. You can also enter a
photograph.
1.2 HOW CHICCO BEBÈCARE EASY-TECH WORKS
Place the child on the seat and secure him with the restraint
systems provided for the type of seat in use.
Use the clip (A) on the white casing of the equipment to attach
the accessory preferably to the shoulder strap of the seat or to
the diagonal portion of the seat belt (Fig.2).
Now completely close the equipment as indicated in Chapter
1.1, paragraph d), item 2. Make sure that the state detected by
the Chicco BebèCare APP is "connected - child seated." From
this moment on, the equipment is active and the presence of
the child can be monitored through the Chicco BebèCare APP.
The alarm system is activated when the smartphone connected
to the equipment moves away from the car in which the ac-
cessory is present.
Chicco BebèCare easy-tech features two alarm levels:
1. First level alarm: should the smartphone move away from
the vehicle with the installed equipment active, the phone will
emit an acoustic and visual alarm that can be muted within 40
seconds. Moving the smartphone towards the equipment does
not stop the alarm. The "STOP" button in the BebèCare APP
must be pressed in order to deactivate the alarm.
2. Second level alarm: this is activated the moment in which
the first level alarm was not silenced within the time window
provided for the first level alarm, and sends alarm messages to
all the predefined emergency numbers with the information
needed for geolocating the area where the baby is located.
At the end of the trip, unbuckle the seat belts, remembering
to always open the equipment (Fig. 3) to deactivate the system
and prevent the alarms from being activated.
The Chicco BebèCare APP comes with a package of alarm
messages" that will decrease with every second level alarm
Werbung
Inhaltsverzeichnis
