IMG STAGELINE MPX-22 Bedienungsanleitung Seite 7

Please unfold page 3. Then you can always see the
operating elements and connections described.
1 Operating Elements and Connections
1.1 Front panel
1 Power switch
2 Level control for the master signal at the output
MASTER (19)
3 Level control for the monitor output BOOTH (20)
4 Level control for the PFL signal at the headphone
output PHONES (9)
5 PFL PAN control for selecting the channel to be
monitored
6 Input selector switches PHONO – CD/LINE for the
channels CH 1 and CH 2
7 LED POWER ON
8 7-step LED VU-meter
9 6.3 mm jack for connecting stereo headphones
(impedance ≥ 8 Ω)
10 Crossfader for crossfading between the channels
CH 1 and CH 2
11 6.3 mm jack (bal.) for connecting a mono micro-
phone; as an alternative to the jack DJ MIC (24) on
the rear panel
12 Volume controls (faders) for the channels CH 1 and
CH 2
13 3-way equalizer for the microphone channel:
HIGH, MID, LOW
14 Level control for the DJ MIC channel
15 PAD switch for the microphone input: With the
switch pressed, the input level of the DJ micro-
phone is attenuated by 20 dB.
16 Gain controls for adjusting the input amplification
for the channels CH 1 and CH 2
17 3-way equalizers for the channels CH 1 and CH 2:
HIGH, MID, LOW
1.2 Rear panel
18 Connection jack 15 V~/1.5 A for the supplied
power supply unit
19 Stereo master output (phono) for connecting an
amplifier
20 Stereo output BOOTH (phono) for connecting a
monitoring system
21 Stereo output REC (phono) for connecting a sound
recorder; the recording level is independent of the
position of the master control (2)
22 Phono input jacks CD/LINE for the channels CH 1
and CH 2 for connecting units with line level (e. g.
tuner, CD player, cassette recorder)
23 Phono input jacks PHONO for the channels CH 1
and CH 2 for connecting turntables with magnetic
system
24 6.3 mm jack (bal.) for connecting a mono micro-
phone; as an alternative to the jack DJ MIC (11) at
the front
25 GND connection for a common ground, e. g. for
turntables
2 Safety Notes
The mixer and the power supply unit correspond to the
directive for electromagnetic compatibility 89/336/
EEC. The power supply unit also corresponds to the
low voltage directive 73/23/EEC.
Attention! The power supply unit is supplied with
hazardous mains voltage (230 V~). Inexpert handling
or modification of the power supply unit may cause
an electric shock hazard. Furthermore, any guaran-
tee claim will expire if the power supply unit or the
mixer has been opened.
Please observe the following items in any case:
The mixer and the power supply unit are suitable for
indoor use only. Protect them against dripping water
and splash water, high air humidity, and heat (ad-
missible ambient temperature range 0 – 40 °C).
Do not operate the mixer or immediately disconnect
the power supply unit from the mains socket
1. in case of visible damage to the mixer, to the
power supply unit, or to the mains cable of the
power supply unit,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled per-
sonnel.
A damaged mains cable must be replaced by the
manufacturer or authorized, skilled personnel only.
Never pull the mains cable for disconnecting the
mains plug from the socket, always seize the plug.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the mixer or the power supply unit
is used for other purposes than originally intended, if
it is not correctly connected, operated, or not re-
paired in an expert way.
Important for U. K. Customers!
The wires in the mains lead of the power supply unit
are coloured in accordance with the following code:
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured blue must be con-
nected to the terminal in the plug which is marked
with the letter N or coloured black.
2. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which is not harmful to
the environment.
GB
7