Technical Data; Before Starting The Equipment - Scheppach MFH5300-4BP Original Bedienungsanleitung

6. Technical data

MFH5300-4BP
Technical data
Cutting data grass trimmer
Cutting circle diameter of line
mm
Cutting line diameter mm
Cutting line length m
Speed grass trimmer max. min¹
Cutting data brush cutter
Cutting circle diameter of
blade mm
Cutter balde thickness mm
Teeth quantity
Speed brush cutter max. min¹
Cutting data hedge trimmer
Cutting circle diameter mm
Angle adjustment °
Cutting length mm
Max. cutting speed max. min
-1
Cutting data pole saw
Bar length mm
Cutting length mm
Cutter bar Type
Saw chain division
Chain type
Chain link thickness
Oil tank capacity cm
3
Speed Pole saw min. min
-1
Power unit
Displacement ccm
Max. engine output kW
Idle speed min
-1
Fuel tank capacity cm
3
Engine type
Weight grass trimmer kg
Weight brush cutter kg
Weight pole saw kg
Weight hedge trimmer kg
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 97,3 dB(A)
pA
Sound power L = 115,2 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration
Grasstrimmer: A = Front 6,67 m/s
hv
Brush cutter: A = Front 6,96 m/s
hv
Hedge trimmer: A = Front 6,62 m/s
hv
Pole saw: A = Front 6,62 m/s
hv
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
450
2 x 2.8
4
7200
255
1.4
3
8500
24
+90°/0°/-75° (165°)
400
1550
305
254
Oregon 100SDEA318
3/8"
91PJ040X
1,27
125
4200
51,7
1300
3000
±300
960
2-stroke engine, air-
cooled
11,98
11,88
12,53
13,20
Rear 5,67 m/s
2 2
Rear 7,14 m/s
2 2
Rear 6,62 m/s
2 2
Rear 3,99 m/s
2 2
Uncertainty K = 1,5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m

7. Before starting the equipment

Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are com-
plete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
1 Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special
2-stroke engine oil. Mix the fuel mixture as indicated
in the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2-stroke oil with a recom-
mended mixing ratio of 100:1. The manufacturer's
warranty will be voided in case of engine damage
due to inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bot-
tle). Then shake the bottle well.
Never use oil for 4-cycle engine or use water cooled
2-cycle engine. It can cause spark plug fouling ex-
haust part blocking or piston ring sticking.
Mixed fuels, which have been left unused for a pe-
riod of one month or more, may clog the carburetor
or result in the engine foiling to operate property. Put
remained fuel into an airtight container and keep it in
the dark and cool room.
GB | 37