Einstellpunkte Für 2-Wege-Übergang - JVC KD-X362BT Bedienungsanleitung

AUDIOEINSTELLUNGEN
X ' OVER (Übergang)
• [FRQ] / [F-HPF FRQ] / [R-HPF FRQ] / [SW LPF FRQ]
Übergangsfrequenz für die gewählten Lautsprecher an (Hochpassfilter oder
Tiefpassfilter).
Wenn [THROUGH] gewählt ist, werden alle Signale zu den gewählten
Lautsprechern gesendet.
• [SLOPE] / [F-HPF SLOPE] / [R-HPF SLOPE]
die Stellt die Übergangsflanke an.
Nur wählbar, wenn eine andere Einstellung als
Übergangsfrequenz gewählt ist.
• [SW LPF PHASE] / [PHASE] : Wählt die Phase des Lautsprecherausgangs so, dass sie
dem anderen Lautsprecherausgang entspricht.
• [GAIN LEFT] / [GAIN RIGHT] / [F-HPF GAIN]
Ausgangslautstärke des gewählten Lautsprechers an.
/ [HPF FRQ] / [LPF FRQ] : Passt die
/ [SW LPF SLOPE] / [HPF SLOPE] / [LPF SLOPE]
[THROUGH]
für die
/ [R-HPF GAIN] / [SW LPF GAIN] / [GAIN]
Einstellpunkte für 2-Wege-Übergang
[SPEAKER SIZE]
[FRONT]
: Passt
[REAR]
*1
: Passt die
[SUBWOOFER] *2*3
[X ' OVER]
[TWEETER]
[FRONT HPF]
[REAR HPF]
*1
*1, *2, *3: (seite 24)
[SIZE] [8CM] [10CM] [12CM]
/ /
[18CM] / [4×6] / [5×7]
[TWEETER] [SMALL] [MIDDLE]
/ /
angeschlossen)
[8CM] [10CM] [12CM] [13CM] [16CM]
/ / / /
[5×7] [6×8] [6×9] [7×10] [NONE]
/ / / / (nicht angeschlossen)
[16CM] / [20CM] / [25CM] / [30CM] / [38CM OVER]
angeschlossen)
[FRQ] [1KHZ] / [1.6KHZ] / [2.5KHZ]
[6.3KHZ] / [8KHZ] / [10KHZ]
[GAIN LEFT] [–08DB] [00DB]
bis
[GAIN RIGHT] [–08DB] [00DB]
bis
[F-HPF FRQ] [30HZ] / [40HZ] / [50HZ]
[90HZ] / [100HZ] / [120HZ]
[220HZ] [250HZ] [THROUGH]
/ /
[F-HPF SLOPE] [–06DB] [–12DB]
/ /
[F-HPF GAIN] [–08DB] bis [00DB]
[R-HPF FRQ] [30HZ] [40HZ] [50HZ]
/ /
[90HZ] [100HZ] [120HZ]
/ /
[220HZ] [250HZ] [THROUGH]
/ /
[R-HPF SLOPE] [–06DB] / [–12DB] /
[R-HPF GAIN] [–08DB] [00DB]
bis
[13CM] [16CM] [17CM]
/ / / /
/ [6×8] / [6×9] / [7×10]
[LARGE] [NONE]
/ (nicht
[17CM] [18CM] [4×6]
/ / / /
/ [NONE] (nicht
/ [4KHZ] / [5KHZ] /
/ [12.5KHZ]
/ [60HZ] / [70HZ] / [80HZ] /
/ [150HZ] / [180HZ] /
[–18DB] [–24DB]
/
[60HZ] [70HZ] [80HZ]
/ / / /
[150HZ] [180HZ]
/ / /
[–18DB] / [–24DB]
23
DEUTSCH