Velleman VTSS5 Bedienungsanleitung Seite 4

3. G General Gu
Refer to t the Velleman®
Indoor
liquids.
Keep th
are clea
Protect
•
Fami liarise yourself
•
All m modifications of t
to th e device is not c
•
Only use the device
warra anty.
•
Dama age caused by d
the d dealer will not ac
•
Do n ot switch the de
Prote ect the device ag
4. Overview O
Refer to t the illustrations
1 pow er cord
2 tem perature contro
3 spon nge
4 iron stand
5. I Instruction
Warning: this
unattended w
5.1 P Preparation
1. Put the soldering ir
2. Mak ke sure the spon
it in the sponge tra
3. Put the soldering ti
Only y change a sold
gen tly pull out the
Wa rning: Never u
5.2 E Electrical Con
Connect the power cord
station is s now ready for
5.3 Temperature T
1. Use the rotary cont
tem mperature.
2. Set the temperatur
to m melt some solde
cloc ckwise, wait a lit
V. 03 – 2 20/06/2012
idelines
® Service and Q Quality Warra
r use only. Kee p this device aw
Never put objec cts filled with liq
is device away from dust and e
ar at all times.
this device from m shocks and ab
with the functio ons of the device
the device are f forbidden for saf
covered by the warranty.
for its intended d purpose. Using
disregard of cer rtain guidelines
ccept responsib bility for any ens
evice on immed iately after it ha
gainst damage by leaving it sw
s on page 2 of th his manual.
5 bit
oller 6 heating eleme
7 antiskid rubbe
8 handle
s
s tool must be e placed on its
when switched d on.
ron holder [4] in n the correspon
nge [3] is comp pletely saturated
y.
p [5] into the s shaft [6] and at
ering tip when t the soldering iro
soldering tip. C heck the screw
use the solderi ing iron witho
nnection
[1] to a 230V/ /50Hz power sup
use.
e setting
trol [2] on the f front panel to sw
re controller [2] ] between the s
er. If it doesn't m melt fluidly, rota
ttle while and tr ry again until it
VTSS S5
anty on the last pages of this m
way from rain, m moisture, splash
quid on top of o or close to the d
extreme heat. M Make sure the v
buse. Avoid brut te force when o
e before actuall y using it.
fety reasons. Da amage caused b
g the device in a an unauthorised
in this manual i is not covered b
suing defects or r problems.
as been exposed d to changes in
witched off until it has reached
ent
er
stand when n not in use; do n
nding hole in the e casing of the s
d with clean wat ter and let it dr
ttach it to the so oldering iron wi
on has cooled d own. Loosen th
fitting regularly y and tighten it
out the solderin ng tip.
pply. The power r LED turns ON
witch the device e on and set the
second and third d scale, wait a fe
ate the tempera ature controller
does.
4
manual.
hing and drippin ng
evice.
entilation openi ings
operating the de evice.
by user modifica ations
d way will void t the
by the warranty and
temperature.
room temperatu ure.
not leave the t tool
soldering station n.
ip off before you u put
th a coupling nu ut.
e coupling nut a and
when necessary y.
and the solderi ng
e desired
ew moments an nd try
[2] a little furth her
©Vellem man nv