Setting The Speed (Fig. M) - DELTA-SPORT DL-5650 Gebrauchsanweisung

• Hover left/right (roll) (Fig. L)
If you want to perform a movement to the right
or left without rotating the Quadrocopter (1),
i.e. hover sideways, move the right control lever
(2l) to the left or right.
• Turning (yaw trimming) (Fig. O)
If the Quadrocopter (1) moves around its own
axis of its own accord without you moving the
control lever (2l) you can correct this with the
yaw-trimming.
If the Quadrocopter (1) turns clockwise, press
the yaw-trim button to the left (2f), and if it turns
anti-clockwise, press the roll-trim button to the
right (2d). In this way you counter the yaw
movement by trimming in the opposite direction.
• Direction (roll and pitch trimming)
(Fig. P)
If there is a forwards or backwards movement,
even though you are not using the control lever
(2l) at all, you can correct this by pitch trim-
ming. If the Quadrocopter (1) is flying forwards,
press the pitch-trimming button (2o) and vice
versa (2m). You can counteract the unwanted
movement with the trim setting.
If the Quadrocopter (1) moves sideways of
its own accord, you can correct this by roll
trimming.
If the Quadrocopter hovers to the left (1)
sideways, press the trimming button (2n) to the
right and vice versa (2p). This allows you to
counteract the unwanted movement.
• Headless Mode (Fig. Q)
This refers to a flight aid that when activated
enables the Quadrocopter (1) to always fly in
the direction it is steered. It is recommended for
pilots with little flying experience.
When headless mode is activated with the
relevant button (2c), from the pilot's viewpoint,
the Quadrocopter (1) always flies to the right
when the control lever (2l) is steered to the
right, regardless of which way the front of the
Quadrocopter (1) is facing.
NOTE: The direction of the remote control
(2) and the Quadrocopter (1) must
correspond exactly when headless mode is
activated!
Only activate headless mode in the position spec-
ified, otherwise it may result in control commands
not being carried out correctly.
1. To activate headless mode, put the Quadrocop-
ter (1) and the remote control (2) behind one
another and press the button (2c) on the remote
control (2). The display (2j) message HEAD-
LESS lights up and the Quadrocopter lights
blink slowly as long as the mode is activated.
2. To deactivate the mode, press the button (2c)
again. On the display (2j), the message NOR-
MAL lights up and the Quadrocopter lights light
up continuously again.
• Automatic return to the pilot (Fig. R)
Press the active button (2c) for about 3 seconds
to have the Quadrocopter return via the same
route flown.
NOTE: Note that the return route can vary
as a result of the Quadrocopter turning. The
process is brought to a halt by repeated pressing
of the button (2c), or by moving the control lever
(2l).

Setting the speed (Fig. M)

You can adjust the flight speed by repeatedly
pressing the buttons (2e, 2g) on the remote control
(2). The default setting is speed 2, from a total of
four speed levels.
The display lights show the various levels (2j).
Speed 1
(beep sounds once)
For first attempts with little flight experience.
Speed 2
(beep sounds twice)
For pilots with some experience.
Speed 3
(beep sounds three times)
For experienced pilots.
Speed 4
(beep sounds four times)
For very experienced pilots.
NOTE: When the remote control is turned
off and on again, the Quadrocopter (1) is
reset to speed 2.
GB 17