Warranty; Environmental Protection - Narex EBD 30-8 Originalbetriebsanleitung

Tool clamping
If the nut (5) is tightened, hold the spindle firmly (8) by one of the two
wrenches (9) and unscrew the nut (5) using the second wrench (9).
Push the tool (6) clamping stalk (6a) in the spring collet chuck as deep as
possible (7). The tool must not protrude from the spring collet chuck by
more than is the dimension "l".
The dimension "l" for tools with stalk diameter (6) and = 6 mm is stated in
the below table:
d (mm)
12
16
20
25
l
d
Tighten the clamping nut (5) by holding the spindle (8) firmly by one of the
two wrenches (9) and screw the nut (5) in, using the second wrench (9).
Caution! First let the new tool run without load for about 1 minute.
Use only well balanced tools of top quality with max. run-out value of
0.1 mm at the outer edge of the tool.
Maintenance and service
Attention! Risk of el. shock. Prior to start any operation, pull
the plug out of the socket!
‰ The vent holes (14) of the engine cover must not get plugged.
After about 100 hours of operation the following works need to be
done:
‰ Check of the brushes length Brushes shorter than 5 mm must be re-
placed with new ones.
Attention! With respect to protection from el. shock and pres-
ervation of the class of protection, all maintenance and ser-
vice operations requesting jig saw case removal must be per-
formed by the authorized service centre only!
The current list of authorized service centres can be found at our website
www.narex.cz, section "Service Centres".
Storage
Packed appliance may be stored in dry, unheated storage place with tem-
perature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage place with tem-
perature not lower than +5 °C with exclusion of all sudden temperature
changes.

Environmental protection

Power tools, accessories and packaging should be sorted for environmen-
tal-friendly recycling.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, power tools
that are no longer suitable for must be separately collected and sent for
recovery in an environmental-friendly manner.
l (mm)
50
50
40
35
a

Warranty

Our equipment is under warranty for at least 12 months with regard to
material or production faults in accordance with national legislation. In the
EU countries, the warranty period for exclusively private use is 24 months
(an invoice or delivery note is required as proof of purchase).
Damage resulting from, in particular, normal wear and tear, overloading,
improper handling, or caused by the user or other damage caused by not
following the operating instructions, or any fault acknowledged at the time
of purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment has not been dis-
mantled before being sent back to the suppliers or to an authorised NAREX
customer support workshop. Store the operating instructions, safety notes,
spare parts list and proof of purchase in a safe place. In addition, the manu-
facturer's current warranty conditions apply.
Information about noise level and
vibrations
The values have been measured in conformity with EN 60745.
Acoustic pressure level L = 82 dB (A).
pA
Acoustic power level L = 93 dB (A).
wA
In accuracy of measurements K = 3 dB (A).
ATTENTION! Noise is generated during work!
Use ear protection!
For EBD 30-8 and EBD 30-8 E:
The weighted value of vibrations affecting hands and arms = 13 m.s
In accuracy of measurements K = 1.5 m.s
Pro EBK 30-8 E:
The weighted value of vibrations affecting hands and arms = 15 m.s
In accuracy of measurements K = 1.5 m.s
The emission values specified (vibration, noise) were measured in accord-
ance with the test conditions stipulated in EN 60745 and are intended for
machine comparisons. They are also used for making preliminary estimates
regarding vibration and noise loads during operation.
The emission values specified refer to the main applications for which the
power tool is used. If the electric power tool is used for other applications,
with other tools or is not maintained sufficiently prior to operation, howev-
er, the vibration and noise load may be higher when the tool is used.
Take into account any machine idling times and downtimes to estimate
these values more accurately for a specified time period. This may signifi-
cantly reduce the load during the machine operating period.
Certificate of Conformity
We declare that the device meets requirements of the following standards
and directivesc.
Safety:
EN 60745-1; EN 60745-2-3
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Directive 2004/108/EC
2010
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
Changes are reserved
English
.
-2
.
-2
.
-2
.
-2
Antonín Pomeisl
CEO of the company
February 1, 2010
17