Vitek VT-1617 Die Betriebsanweisung Seite 4

ENGLISH
the attachments holder (7) with the knife at-
tachment (8), and then remove products from
the bowl, using the spatula (20).
Note: Time of continuous operation of the unit
depends on the product itself and on the grinding
degree, you want to get, and time of continuous
operation should not exceed 1 minute.
Attention!
Be careful when holding the knife attachment
as it has sharp edges.
Beating and making dough
1. Set the drive shaft (4) into the grooves on the
electro motor unit (5).
2. Set the processor bowl (3) on the drive shaft
(4) and lock it, turning clockwise.
3. Set the attachments holder inside the pro-
cessor bowl (7).
4. Set the attachment for blending/ beating (9)
or the dough attachment (10) on the attach-
ments holder (7).
5. Put the necessary quantity of products into
the processor bowl (3).
6. Close the bowl (3) with the lid (2) and turn the
lid clockwise, to match the ledge on the lid
with the deepening on the bowl.
7. Insert the plug into the socket.
8. Switch on the processor, by setting the han-
dle (6) to the II position.
9. After operation, switch off the processor, by
setting the handle (6) to the "O" position, and
take the plug out of the socket.
10. Remove the processor bowl (3), by turning
it counterclockwise, remove the lid (2), the
attachments holder (7) with the attachment
(for blending/beating (9) or for dough mak-
ing (10)), then remove the products from the
bowl, using the spatula (20).
Attention!
•
Never use the attachment (9) for dough making.
•
Do not exceed the quantity of liquid products
in order to avoid splashing.
Using graters/shreddings
1. Set the drive shaft (4) into the grooves on the
electro motor unit (5).
VT-1617.indd 4 VT-1617.indd 4
2. Set the processor bowl (3) on the drive shaft
(4) and lock it, turning clockwise.
3. Set the required grater (12, 14) or the knife for
cutting (shredding) (13) into the disc for at-
tachments setting (11).
4. Set the disc (11) into the processor bowl (3)
on the drive shaft (4).
5. Close the bowl (3) with the lid (2) and turn the
lid clockwise, to match the ledge on the lid
with the deepening on the bowl.
6. Insert the plug into the socket.
7. Switch on the processor, by setting the han-
dle (6) to the II position.
8. Put the products into the throat of the lid (2),
use the pusher (1) to supply products. Press
the pusher with slight effort to feed products.
9. After operation, switch off the processor, by
setting the handle (6) to the "O" position, and
take the plug out of the socket.
10. Remove the chopped products from the bowl
(3).
11. Clean, wash and dry all the details immedi-
ately after operation.
Attention! Time of continuous operation should
not exceed 40 sec.
Blender bowl
Using the blender you can cook up to 1,5 l of liq-
uid or thick soup, compote, beat milkshake, ice-
cream etc.
You can cook any types of liquid dough.
1. Set the seal ring (19) into the grooves on the
electro motor unit (5).
2. Set the blender bowl knives set (18) on the
seal ring (18) and turn it counterclockwise for
fixation.
3. Make sure that the blender bowl knives set
(18) is properly set.
4. Set the blender bowl (17) on the electro mo-
tor unit (5) and turn it clockwise until fixation.
5. Remove the lid (16) and put the necessary
products into the blender bowl (17).
6. Close the blender bowl (17) with the lid (16)
and then insert the plug into the socket.
7. Switch on the processor, setting the handle
(6) to the II position or use the pulse mode,
to do it set the handle (6) to the (Р) "PULSE"
position.
4
14.06.2011 10:49:41 14.06.2011 10:49:41