Schraubenbeutel; 1X Fastener Bag; Care And Maintenance; 1X Sachet De Vis - ATIKA LSH 3000-2 Originalbetriebsanleitung

While working:
 Spectators must observe safety clearance of min. 5 m.
 Beware of swirling and flying objects. Be particularly aware
of recoiling effects from brickwork or house walls (e.g.
stones).
 Switch off the machine before crossing gravel or grit paths.
 Only operate the machine in walking speed, do not run
with it.
 Do not fill anything by hand into the suction hole.
 Never put objects manually into the suction opening.
 Always ensure that the connection lead runs back away
from the machine. Otherwise there is a risk of stumbling,
slipping or falling.
 Never use the machine
without the bag,

without closing the zip fastener of the bag

 Immediately switch off the unit and allow it to come to a
stop if foreign objects enter the unit or if the unit starts to
make unusual noises or vibrates. Remove the mains plug
and carry out the following checks:
inspect for damage,

have damaged parts replaced or repaired,

check the equipment and tighten loose parts.

Before using the machine, ensure that the bag has
been fitted, is not damaged or worn and the zip
fastener has been closed.
Power off the machine before attaching or removing
the collecting bag.
Instructions for using as vac/shredder
Move the changeover switch to the vac/
shredding setting.
 Hold the machine firmly at the handle and
place the belt over your shoulder. Adjust
the belt so that the machine can be carried comfortably
and safely.
Switch the machine on.
Move the machine slowly and evenly over the material.
Do not press it into the leaves.

The suction power decreases when the bag is full.
Switch the machine off and disconnect from the mains.
Open the zip fastener and empty the bag.
After finishing work, move the changeover switch to the
blowing setting to remove any remains from the suc
tion/blowing pipe.

Take up leaves in good time! – It is advisable to take
up fallen leaves when the weather is dry and as soon as they
have fallen. Wet leaves are a problem, together with leaves
that have already begun to rot or are on big piles.
Using the Vacuum Booster

The Vacuum Booster (11) can be used for vacuuming
most foliage and increases the suction power.
Insert it into the recesses in the front of the suction pipe
(9).
16
Move the suction pipe over the material to be sucked up.
Small stones, which are sucked in as well, do not get into the
chipping turbine for the most part.
After switching off the leaf sucker, the small stones fall out
again.
If you want to vacuum heavy and large leaves, remove the
insert.
Instructions for use as blower
Move the changeover switch to the blowing
setting.
 Hold the machine firmly at the handle and
place the belt over your shoulder. Adjust the belt
so that the machine can be carried comfortably and
safely.
Switch the machine on.
Move the suction/blowing pipe in generous swaying
movements uniformly a few centimetres over the
ground, moving from one side to the other.
Blow in the direction of the wind
Garden vac with speed control
This version has adjustable motor speed and therefore
adjustable vacuuming and blowing.
The speed is fully variable from 8000 rpm to
14000 rpm.
 What can I vacuum and blow?

light, dry materials, e.g. dry leaves and garden waste
such as grass, small twigs and pieces of paper

heavy materials such as metal, stones, branches, fir
cones or broken glass
Do not use the machine to vacuum or blow any
burning, explosive or smoking items such as
cigarettes, matches or hot ash.
Do not vacuum or blow any liquids, in particular
flammable liquids such as fuel. Do not use the
machine in the vicinity of such substances.

Care and maintenance

Before each maintenance and cleaning work :
switch off device

wait for standstill of the device

 allow the machine to cool down
pull out main plug

Replace any worn or damaged parts for safety reasons.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance and repair work beyond this is only allowed to be
carried out by the manufacturer or authorized service staff.