Bosch GCM 10 MX Professional Originalbetriebsanleitung Seite 24

24 | English
(41) Saw blade
(42) Inner clamping flange
(43) Wing bolt for adjusting the height of the threaded
rod
(44) Threaded rod
(45) Detents for standard mitre angles
(46) Screws for insert plate
(47) Hex socket screw for fence
(48) Screw for bevel angle indicator
Technical Data
Mitre saw
Article number
Rated power input
No-load speed
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
Permitted workpiece dimensions (maximum/minimum): (see "Per-
missible workpiece dimensions", page 27)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Hole diameter
Noise Information
Noise emission values determined according to EN
62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power level
105 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
1 609 92A 4YL | (14.05.2019)
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Check to ensure that all the parts listed below have been
GCM 10 MX
supplied before using the power tool for the first time:
3 601 M29 02.
– Mitre saw with mounted saw blade
3 601 M29 0P.
– Dust bag (19)
W 1700
– Screw clamp (18)
-1
min 4800
– Hex key/cross-headed screwdriver (22)
– Tilt protector (24) with fastening set (35) (2 bolts, 2
kg 16.8
washers, 2 square nuts)
Note: Check the power tool for possible damage.
/ II
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
mm 254
If the protective devices or any parts become damaged, you
mm 1.8−2.8
must have them properly repaired or replaced by an author-
mm 30
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Mounting the tilt protector (see figure A)
Before the power tool is used for the first time, the tilt pro-
tector (24) must be installed.
Use the "tilt protector" fastening set (35) for the installation.
– Insert the square nuts (35) into the corresponding
holes (34) in the base plate.
– Place the washers (35) on the fastening screws (35) and
use them to screw the tilt protector (24) into the inserted
nuts.
Do not remove the tilt protector. Without the tilt pro-
u
tector, the power tool will not be stable and can tip over
especially when sawing maximum mitre/bevel angles.
Fitting the extension bar (see figure B)
The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
To extend the saw table further, extension bars can be
mounted both to the left or right of the power tool.
See the list of items included at the start of
the operating manual.
Bosch Power Tools