Vitek VT-2503 BW Betriebsanweisung Seite 4

ENGLISH
is damaged; if the unit malfunctions or after it
fell into water. Apply to the authorized service
centre for repair.
• Before you take the unit away, let it cool down,
do not wind the power cord around the unit.
THE UNIT IS INTENDED FOR HOUSEHOLD US-
AGE ONLY.
Switching on of the hairdryer
Before using the unit, make sure that the voltage
of the electric network corresponds to the oper-
ating voltage of the hairdryer.
- Unwind the power cord completely.
- Insert the plug into the socket.
- Use the switch (6) to set the required air sup-
ply speed:
Note: When low or high speed of air supply is
switched on, the operating indicator (2) will
light up.
"0" – off
- low speed
- high speed
- Use the switch (5) to set the required air flow
temperature.
- low heating
- medium heating
- maximal heating
Hair care
To get the best results (before drying or styling)
wash your hair with shampoo, dry it with a towel
to remove excessive moisture and then comb.
Quick drying
Set the switch (5) to the maximal heating posi-
tion (position ), use the switch (6) to set the re-
quired air supply speed and dry the hair. Shake
off excessive moisture from the hair with your
hand or a comb and constantly move the haird-
ryer over the hair.
Straightening
Set the switch (5) to the maximal heating posi-
tion (position ), use the switch (6) to set the
required air supply speed, the operating indica-
tor (2) will light up, and preliminary dry the hair.
When the hair is almost dry, set the concentra-
tor-attachment (1), and use the switch (5) to de-
crease air heating degree and the switch (6) to
decrease air supply speed.
VT-2503.indd 4
Divide hair into locks and layers, start straight-
ening from lower layers. Use a round or a flat
brush to comb your hair downwards and si-
multaneously direct hot air, outgoing from the
concentrator- attachment, at it. This way, slowly
straighten each lock from roots to tips. When you
finish straightening the locks of the lower layer,
start straightening the locks of the medium layer
and finish the process straightening locks of the
upper layer.
Natural wavy structure of the hair
Set the switch (5) to the low heating position
(position ), select air low speed supply, setting
the switch (6) to the
indicator (2) will light up, strongly press the locks
between your fingers, turn them to the natural
curving side and dry them, directing air flow be-
tween the fingers. When you reach the desired
effect, press the "cool" air supply button (4) and
fix each lock.
Styling
Set the switches (5,6) to the low heating/low
speed position and set the concentrator attach-
ment (1) for directed air flow.
Divide hair into locks and create a style using a
round brush for styling. While creating a style di-
rect the air flow at the hair in the desired direc-
tion.
If necessary, direct the air flow at each lock dur-
ing 2-5 seconds to fix your hair.
Chose the time, which is necessary for styling
according to your hair type.
"Cool" air supply
In this model the "cool" air supply function is
provided, the "cool" air being used to fix your
hair-do. Press and hold the "cool" air supply
button (4) – it will allow you to keep the created
style of the hair-do.
Overheating protection
The unit has the protection from overheat-
ing function, which will switch off the unit if the
temperature of output air increases. If the unit
switches off during its operation, switch it off
with the switch (6), setting it to the "0" position,
take the plug out of the socket, make sure that
the air openings are not blocked, let the unit cool
4
position, the operating
12.11.2012 14:26:50