Functional Description - Makita TD022D Betriebsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
► Fig.1: 1. Button 2. Battery cartridge
To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place.
CAUTION:
Always insert it until it locks in
place with a little click. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The tool will automatically stop during operation if
the tool and/or battery are placed under the following
condition:
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. If you turn the tool on, the motor runs
again but stops soon. In this situation, remove and
recharge the battery.
Lock lever
CAUTION:
When not operating the tool,
always set the lock lever in the locked position
► Fig.2: 1. Lock lever 2. Switch
When the lock lever is in the locked position
switch cannot be actuated.
When the lock lever is in the unlocked position
switch can be actuated.
Switch action
CAUTION:
the tool, always check to see that the switch trigger actuates
properly and returns to the "OFF" position when released.
CAUTION:
rotation before operation.
NOTICE:
comes to a complete stop. Changing the direction
of rotation before the tool stops may damage the tool.
To start the tool, first move the lock lever to the
unlocked position
► Fig.3: 1. Lock lever 2. Switch
And then turn the switch to A side for clockwise rotation
or to B side for counterclockwise rotation.
Tool speed is increased by increasing rotation angle on
the switch. Release the switch to stop.
► Fig.4: 1. Switch
Lighting up the front lamp
CAUTION:
source of light directly.
To turn on the lamp only, first move the lock lever to the unlocked
position
Release the switch to turn off the lamp.
► Fig.5: 1. Lamp 2. Lock lever 3. Switch
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
socket bit
► Fig.6
Use only driver bit/socket bit that has inserting portion shown
in the figure. Do not use any other driver bit/socket bit.
For tool with shallow driver bit hole
A=12mm
B=9mm
.
For tool with deep driver bit hole
A=17mm
, the
B=14mm
A=12mm
, the
B=9mm
6 ENGLISH
Before installing the battery cartridge into
Always check the direction of
Change the direction only after the tool
to release the switch.
Do not look in the light or see the
. And then rotate the switch to the A or B side a little.
Always be sure that the tool is
Use only these type of driver
bit. Follow the procedure
1. (Note) Bit-piece is not
necessary.
To install these types of driver
bits, follow the procedure 1.
To install these types of driver
bits, follow the procedure 2.
(Note) Bit-piece is necessary
for installing the bit.