Functional Description - Makita VR004G Betriebsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Replacing battery case
Optional accessory
Install one of the battery cases optionally available in
three ranges of sizes to fit your battery cartridge and
cord connected power source.
► Fig.1: 1. Battery case S 2. Battery case L 3. Battery
case H
1. Open the standard equipped battery case while
pressing the buttons on sides of the case.
2. Loosen the screws securing the standard
equipped battery case, and slide the battery case off
along the housing.
► Fig.2: 1. Standard equipped battery case 2. Screws
3. Housing
3.
Slide an optional battery case into the tool. Open
the case while pressing the buttons on sides of the
case. Then tighten the screws to secure it in place.
► Fig.3: 1. Optional battery case 2. Screws
4. Close the battery case securely.
Installing and removing battery
cartridge
CAUTION:
Before installing and removing
battery cartridge, always make sure to set the
switch trigger back into the "OFF" position by
pulling the switch trigger fully and releasing it.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION:
Take care not to trap your fingers
between the battery case and its front cover while
installing and removing battery cartridge.
Installation
1.
Open the battery case while pressing the buttons
on sides of the battery case.
► Fig.4: 1. Battery case 2. Buttons
2. Insert a battery cartridge in place aligning its
tongue with the groove on the tool. If you can see the
red indicator as shown in the figure, it is not locked
completely.
► Fig.5: 1. Red indicator 2. Battery cartridge
3.
Close the battery case securely.
Uninstallation
1. Open the battery case while pressing the buttons
on sides of the battery case.
2. Slide the battery cartridge off from the tool while
pressing the button on front of the battery cartridge.
► Fig.6: 1. Button 2. Battery cartridge
3. Close the battery case securely.
For cord connected power source
Optional accessory
Replace the standard equipped battery case with an
optional battery case H before installation.
Installation
1. Open the battery case while pressing the buttons
on sides of the battery case.
2.
Insert a battery adapter in place aligning its tongue
with the groove on the tool. If you can see the red indi-
cator as shown in the figure, it is not locked completely.
► Fig.7: 1. Red indicator 2. Battery adapter
3. Open the rubber sealing grommet in the battery case.
Make sure to squeeze the rubber sealing grommet out of
the round hole rim from inside the front cover of the case.
► Fig.8: 1. Rubber sealing grommet 2. Front cover
4.
Pass the adapter plug and plug cord through the
round hole in the battery case.
► Fig.9: 1. Adapter plug 2. Plug cord 3. Battery
adapter
5. Close the battery case securely.
6.
Place the rubber sealing grommet back in place.
► Fig.10: 1. Rubber sealing grommet 2. Plug cord
3. Battery case
Uninstallation
1. Open the battery case while pressing the buttons
on sides of the battery case.
2. Open the rubber sealing grommet in the battery case.
Make sure to squeeze the rubber sealing grommet out
of the round hole rim from inside the front cover of the
case.
► Fig.11: 1. Rubber sealing grommet 2. Front cover
3.
Pull the adapter plug and plug cord out through
the round hole in the battery case.
4. Slide the battery adapter off from the tool while
pressing the button on front of the battery adapter.
5. Close the battery case securely.
9 ENGLISH