T.O.M GSS13V Originalbetriebsanleitung Seite 12

WARNING !
Read the instructions in full. Any failure to comply with the instruc-
zards or serious injury. The term "power tool" mentioned in all of
the warnings listed below refers both to the power tool when it is
connected to the mains (by the power cord) and when it operates
on its battery (without cables).
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE USE.
1) Work area
a) Keep the work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres or in the
rate sparks which may ignite the dust or fumes.
c) Keep onlookers and children away from the work area while
operating a power tool. Distractions can cause you to lose control
of the tool.
2) Electrical safety
a) The power tool plug must correspond to the wall socket. Do
not modify the plug in any event. Do not use an adapter plug with
power tools that must be connected to the earth. The original
plugs and suitable wall sockets reduce the risk of electric shock.
b) Avoid body contact with earthed surfaces such as piping, ra-
diators, refrigerators, etc. The risk of electric shock is increased if
your body is connected to the earth.
c) Do not expose power tools to rain or humidity. Water entering a
power tool increases the risk of electric shock.
d) Take care of the electrical cord. Never transport, pull or dis-
connect the power tool by pulling on the cord. Keep the cord
away from heat, greasy material, sharp edges and moving parts.
Damaged or tangled cords increase the risk of electric shock.
e) Only use an extension cord that has been designed for outdoor
use when operating the power tool outdoors. Using a cord for
outdoor use reduces the risks of electric shock.
3) Personal safety
a) Stay alert and watch what you are doing. Use common sense
when operating a power tool. Do not use the power tool when
moment of inattention can lead to serious injury.
b) Use personal protective equipment. Always wear protective
goggles. When required, use safety equipment such as a dust
mask, non-skid safety shoes, a hard hat and hearing protection to
reduce the risk of injury.
c) Avoid unintentional starting up. Ensure the switch is in the off-
position before you connect the tool.
them with the switch set to on can lead to injuries.
d) Remove any adjustment keys or wrenches before starting up
the power.
If a key or wrench remains attached to a moving part, there is a
high risk of injury.
e) Do not bend too far over the tool. Keep your balance and a
12
700606-Manual-C.indd 12
GENERAL SAFETY INSTRUCTIONS
proper footing at all times to keep closer control of the power tool
in unexpected situations.
-
f) Wear appropriate clothing. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewellery or hair are likely to be caught by moving
parts.
g) If the tool is equipped with a connection for sawdust exhaust or
dust recovery systems, ensure that they are connected and used
correctly. Using this equipment can reduce the risks connected to
dust.
4) Tool use and care
-
a) Do not force the power tool. Use the correct power tool for your
application. This will provide better results and will be safer if the
power tool is used at the speed for which it is designed.
b) Do not use the power tool if it cannot be started up and stop-
ped using the switch. A power tool that cannot be controlled by
means of the switch is hazardous and must be repaired.
c) Disconnect the power tool from the mains or remove the bat-
tery before making adjustments, changing accessories or storing
it. These preventive safety measures reduce the risk of starting
the tool accidentally.
d) Store power tools switched off and out of the reach of children.
Do not give them to untrained individuals who have never used
them before and have not read and understood these instructions.
Power tools can be dangerous in the hands of these individuals.
e) Take care of you power tools. Check the misalignment or
binding
of moving parts, breakage of any parts and any other condition
that could hinder the working of the power tool. If the tool is da-
maged, have it repaired immediately. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools clean and sharpened. Well maintained cut-
ting tools with sharp cutting edges are less like to bind and easier
to control.
g) Use the power tool, accessories, disc pads, etc. in accordance
with these instructions and according to their characteristics, de-
pending on the task to be carried out and the working conditions.
Using a power tool for reasons other than those for which it was
designed can be dangerous.
5) Repairs
uses identical spare parts. This is vital in order to ensure that the
power tool can be used safely.
31/08/15 11:28:25