System Information - Husqvarna HMI:FS5000 D Bedienungsanweisung

System information

FS 5000 D
1
Control Panel
SN (Serial Number)
HW (Hardware Number)
SW (Software Number)
BL (Bootloader Number)
2
Engine
Serial Number
Model Number
Engine Working Hours
Engine Working Hours in low idle
Time Since Last Regeneration
3
Engine Working Hours left until
regeneration must be performed
1. Product model.
2. Remaining time in which a regeneration must be
done. If a regeneration is not done in this time, the
engine goes into backup mode. Only applicable for
FS5000 D. Refer to the operator's manual for
FS5000 D.
3. Go back in the menu structure.
4. Select to read the GPL license information.
5. Engine information
6. Time since last regeneration. Only applicable for
products that comply with the Euro V Emission
standard.
7. Select to clear the time that the engine has operated
in low idle speed. A PIN code is necessary.
Gearbox and blade information
This view shows the recommended gear, rpm, pulley
and flange setups for available blade dimensions.
Note: The tables for 1-speed gearbox and 3-speed
gearbox look different. The illustration shows the table
for a 3-speed gearbox.
Product configuration for different blade
Refer also to
dimensions on page 7 .
2
n
1
N N
1 min
3
Select
[Maximum]
GEAR
2
N 1 N
3
3
2
2
1
3 4
1. Select product configuration. Refer to
blade information selection on page 4 .
2. Go back in the menu structure.
3. Gearbox range.
4. Cutting blade diameter, mm/in.
5. Blade flange diameter, mm/in.
6. Maximum blade speed.
7. Diameter of the blade shaft pulley, mm/in.
4
GPL
License
: YYYYWWXXXXX
: 580844701-NA
: 123456789-A0001
: 815361XX-AXXXX
: NA
: NA
: 123:50 (hh:mm)
: 12:30 (hh:mm)
: 34:10 (hh:mm)
Clear Low
Idle Time
: 3:00 (hh:mm)
GEARBOX RANGE / BLADE RPM
n
+
min
[14-26, FS 50000 D]
BLADE ENGINE
BLADE
FLANGE
SIZE
SIZE
RPM PULLEY RPM PULLEY
Ø
n n
Ø
min min
Ø Ø
14" 3100
20" 6" 2170 4.17" 3000 4.51"
26" 1860
5 6 7 8 9
Gearbox and
8. Maximum engine speed.
9. Diameter of the gearbox pulley, mm/in.
4
Gearbox and blade information selection
5
Select your product to get the correct gearbox and blade
information.
6
7
1
1. Go back in the menu structure.
2. Move up in the list of available selections.
3. Move down in the list of available selections.
4. Select product configuration.
Engine fault codes
1
Engine
2
Non
Engine
3
If there are no active or passive engine fault codes, a
message with this information shows on the display
when you open this view.
1. Engine fault codes. The different color shows that
this view is selected.
2. Select to open the view for fault codes that are not
related to the engine.
3. Go back in the menu structure.
4. Move up in the list of fault codes.
5. Move down in the list of fault codes.
6. Select between active and passive engine fault
codes.
FS 5000 D, 1-Speed US
FS 5000 D, 1-Speed EU
FS 5000 D, 3-Speed 14-26 US
FS 5000 D, 3-Speed 20-30 US
FS 5000 D, 3-Speed 20-36 US
FS 5000 D, 3-Speed 350-650 EU
FS 5000 D, 3-Speed 500-750 EU
FS 5000 D, 3-Speed 500-900 EU
Active Engine Faults
SNP:523612
FMI: 12
OCC: 1
SNP:457 FMI: 3
OCC: 1
SNP:523615 FMI: 5
OCC: 1
SNP:523615 FMI: 3
OCC: 1
1247 - 001 - 09.07.2019
2
3
4
4
5
6
Show
Passive
Faults