Maintenance - Elica Platinum Montage- Und Gebrauchsanweisung

Control of the lateral lights (when envisaged)
The lateral lights can be switched on and off by touching the
LOWER PART of the control bar CONTINUOUSLY.
A CONTINUOUS TOUCH allows, other than switching on and
off, adjusting the intensity of the light of the lamp.
Using the remote control
The remote control is able to control all the functions of the
hood:
Select the suction speed (power)
Control the central light
Control the lateral lights
Reset e configure the saturation of the filters signal
Selecting the suction speed (power):
Press the "◄" key or the "►" key until you see the symbol
relating to the "Select the suction speed (power)" function.
Press the "+" key or the "-" key or the "■" key respectively to
increase or diminish or switch off (stand-by) the speed
(suction power).
Controlling the central light:
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Controlling the central light" function on the
remote control.
The central light can be switched on and off in two ways:
1. Press the "+" key or the "-" key respectively to switch the
central light (ON) or (OFF).
2. Press the "■" key to change the state of the light from
(OFF) to (ON) or vice versa.
Controlling the lateral lights:
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Controlling the lateral lights" function on the
remote control.
Press the "■" key to change the state of the lateral lights from
(OFF) to (ON) at maximum intensity and vice versa.
Press the "-" key to diminish the intensity of the lateral lights
until switching them off.
Press the "+" key to increase the intensity of the lateral lights.
Resetting and configuring the saturation of the filters
signal
Switch the hood on at any speed (see paragraph above
"Selecting the suction speed (power").
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Resetting and configuration of the saturation of
the filters signal" function on the remote control.
Resetting the anti-fat filter saturation signal (GREEN LED
FLASHING on the control bar)
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Press the "+" and "-" keys contemporaneously for about 3
seconds. The LED stops flashing, indicating that the resetting
of the signal has been accomplished.
Resetting the carbon filter saturation signal (ORANGE
(amber) LED FLASHING)
Note! The reset of the carbon filter saturation signal is
normally deactivated. To activate it, see under paragraph
"Activating the carbon filter saturation signal".
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Press the "+" and "-" keys contemporaneously for about 3
seconds. The LED stops flashing, indicating that the resetting
of the signal has been accomplished.
Activating the carbon filter saturation signal
The reset of the carbon filter saturation signal is normally
deactivated. To activate it, proceed as follows:
Switch the hood off (see paragraph above "Selecting the
suction speed (power)").
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Resetting and configuration of the filters
saturation signal" function on the remote control.
Press the "+" and "-" keys contemporaneously for about 3
seconds. The LED will flash in ORANGE (amber).
To deactivate the carbon filter saturation signal, repeat the
operation. The LED will flash in GREEN.
Maintenance of the remote control
Cleaning the remote control:
Clean the remote control with a damp cloth and a neutral
solution of detergent without abrasive substances.
Changing the battery:
• Open the battery casing using a small screwdriver with a
flat point.
• Change the finished battery with a new one of 12 V type
MN21/23
In inserting the new battery respect the polarity indicated
on the battery casing!
• Close the battery casing up again.

Maintenance

Prior to any maintenance operation ensure that the cooker
hood is disconnected from the power supply.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
Warning: Failure to carry out the basic standards of the
cleaning of the cooker hood and replacement of the filters may
cause fire risks.
Therefore we recommend observing these instructions.
6