Making Settings; Time Settings - Grohe Ondus series Installation

Note: It must be ensured that the movement is not disrupted
by obstacles.
To prevent falsification of the servo motor adjustment, lever (P2)
must not be removed.
Calibration has been completed when lever (P2) is at
approx. 90°, see Fig. [19].
Note: Do not disconnect the servo motor from the electronics
following calibration.
Installing the servo motor
1. Disconnect electronics (C) from extension cable (D),
see Fig. [19].
2. Engage servo motor (P) in crossrail (U) in the cistern,
see Fig. [20].
Note: The servo motor must be fastened to the side of the
crossrail which is opposite the filler valve.
3. Insert lift rod (O) through the opening in lever (P2) from the
rear, see Fig. [21].
If the servo motor is located on the left side of the crossrail,
insert lift rod (O) through the opening in lever (P2) from the
front.
4. Connect the voltage supply: Connect electronics (C) and
extension cable (D).
5. Make settings.
Installing the wall plate
1. Push the extension cable into the empty tube until the
plug-in connector no longer protrudes into the cistern.
2. Fasten the wall plate on the magnets, see Fig. [22].

Time settings

Button
(*1) / (*2)
Time
(factory setting: 19:00)
Start time for lighting
(factory setting: 19:00)
Lighting duration
(factory setting: 3:00)
Flashing signals:
Confirmation Press and hold
via 4 LEDs (V), button for 5 s
see Fig. [24]
(*1): Confirmation "time programming is activated": 3 fast flashing signals then continue with:
and/or button T2 (minutes selection)
(*2): If no further button is pressed within 30 s after the confirmation "time programming is activated", time setting mode is exited
without changing the time.
(*3): If button T3 (save) is not pressed within 30 s after selecting hours and/or minutes, time mode setting is exited without
changing the time.
(*4): Confirmation "setting has been saved": 3 fast flashing signals, then: normal mode.
Daylight saving setting (summer/winter time)
• To put the time back 1 hour, press and hold buttons T1 and T2 simultaneously for more than 5 s.
• To put the time forward 1 hour, press and hold buttons T2 and T3 simultaneously for more than 5 s.
Restoring the factory setting
To restore the factory setting, press and hold buttons T1, T2 and T3 simultaneously for more than 5 s.
5

Making settings

Remove the wall plate, see Fig. [23].
Colour setting
Functions with button T1, see Fig. [24]
1. Pressing button T1 for the first time switches on the lighting.
2. Pressing button T1 for the second time activates the set
timer. Confirmation: Illuminated frame flashes.
3. Pressing button T1 for the third time switches off the lighting.
Switching colour using button T2, see Fig. [24]
The lighting can be switched between the colour white and
a stored colour/the colour cycle.
1. Switch on lighting using button T1.
2. Each press of button T2 switches the lighting between the
colour white and the stored colour/the colour cycle.
Selecting colour using button T3, see Fig. [24]
1. Switch on lighting using button T1.
2. Each press of button T3 starts or stops the colour cycle.
The most recently displayed colour/the colour cycle is stored.
The stored setting is displayed using button T1 and can be
switched using button T2.
Start: Button T1:
Hours selection
via flashing signals
1. Flashing signals:
2. Flashing signals:
T1
...
24. Flashing signals:
T2
1. Flashing signals:
...
T3
23. Flashing signals:
24. Flashing signals:
Press and hold button until the number of flashing
signals corresponds to the desired number of hours
Button T2:
Minutes selection
via flashing signals
1:00 1. Flashing signals = 5 min
2:00 2. Flashing signals = 10 min
0:00 ...
11. Flashing signals = 55 min
12. Flashing signal = 0 min
1 h
23 h
0 h
and minutes
button T1 (hours selection)
Button T3:
saving
(*3) / (*4)
Hours and/or minutes
as selected with T1/T2
after saving:
Normal mode