Mute Button - auna 10005071 Handbuch

MUTE BUTTON

9.
This button serves to switch the MUTED state on/off. Press the MUTE button to suppress the loudspeaker
temporarily, and press again to resume listening. The muted state will be also released when the MODE,
SEL button is pressed and VOL knob on the front panel is used.
APS BUTTON (Auto-storage /Preset scan)
10.
During radio mode:
When press and hold for more than 1 second, the radio searches from the current frequency and
1)
checks the signal strength level until 6 station are found. And then the 6 stations frequency are preset to
the corresponding preset memory numbered bank. The auto-storage operation is implemented in the
each selected band. When the auto-storage operation is finished, the radio execute the Preset Scan.
when short pressing, the radio searches for each preset station in the current band and holds at that
2)
preset number for 5 seconds with releasing mute, and then search again.
During MP3 file in disc, SD or USB mode, press the APS button briefly, it is activated
Rotate the VOL knob to select and enter the number on the flashing digit place from 0 to 9.
Then press the APS button to confirm the entered number and the 0 on the tens digit will be flashing.
Rotate the VOL knob to select and enter the number on the flashing digit from 0 to 9. Then press the
APS button to confirm the entered number and the 0 on the units place digit will be flashing.
Rotate the VOL knob to select and enter the number on the flashing digit from 0 to 9. After finishing
enter all the number of the song serial number on the flashing digit, press the SEL button to play the
corresponding track.
11. PRESET STATION MEMORYAND TOP/>||, INT, RPT, RDM BUTTONS
a) During radio mode:
Go to any preset station by pressing one of the 6 preset station buttons (1-6).
If one of these buttons is pressed for more than 2 seconds, the station currently being listened to will be
memorized into the selected preset button.
b) During disc, SD or USB mode:
Press the TOP/ >|| button briefly to interrupt the playback of the disc, SD or USB. Press again to
1)
resume normal playback of the disc, SD or USB. Press the TOP/>|| button and hold for approximately
0.5 seconds to play the first track of the disc, SD or USB.
Press the INT button to sample the first 10 seconds part of each track, and the INT ON will be visible
2)
on the LCD display. In the process of INT, press INT button again to stop sampling and to continue
playing the current track, and the LCD will display INT OFF.
Press the RPT button once to play the current track repeatedly, and the RPT ONE will be visible on
3)
the LCD display. During MP3 disc, SD or USB mode, press the RPT button twice continuously to play
the current folder repeatedly, and the RPTABM will be visible on the LCD display. In the process
of RPT, press RPT button again to stop playing repeatedly mode and the LCD will display RPT
OFF.
Press the RDM button to play all tracks on disc in random order, and the RDM ON will be visible on
4)
the LCD display. In the process of RDM, press RDM button again to stop playing in random order
12. AF [ALTERNATIVE FREQUENCIES] BUTTON
When pressed short, AF switching mode is selected and the state of AF switching mode is displayed by
AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all the time. The interval
of checking time of each AFs depends on the signal strength of current station, from a few minute for
strong station to a few seconds for weak station. Every time that new AF is stronger than current station,
it switches over to that frequency for very short time, and NEW FREQUENCY is displayed for 1 -2 second.
Because the mute time of AF switching or checking time is very short, it is almost inaudible in case of
normal program. During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only
receive and save RDS program.
When pressed long, AF mode is converted to REGION ON/OFF mode. REGIONAL MODE ON:
AF switching or PI SEEK is implemented to the station which have all PI codes are same as current
station.(PI CODE is checked when AF CHECK in progress) REGIONAL MODE OFF:
The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented.
(PI CODE and COVERAGE AREA is not checked when AF CHECK in progress)
13. TA [TRAFFIC ANNOUNCEMENT] BUTTON
(1) When press the button, it is activated as TA mode on or off. When TA mode is on (TA is displayed on
LCD), it will begin to seek TA station and TA SEEK will be displayed on LCD for a while.
When traffic announcement is transmitted:
1) If the unit is in SD, USB or disc mode, it will switch to radio mode temporarily.
2) Temporarily switch over to an EON linked station when EON detects a traffic announcement on
that other program, and TP will be displayed on LCD