auna 10005071 Handbuch Seite 13

If volume level is below 20, volume level is raised to 20, and returns to its previous mode
3)
and volume level when the traffic announcement is over. If volume is adjusted during traffic
announcement, only the traffic announcement volume is valid.
 TA interruption function:
The current traffic announcement is cancelled by pressing this key. But the TA mode will not be off.
 When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or saved only
when traffic program identification code has been received. When TA is ON, traffic program
identification code is not received during specified time.
(2) When pressed long, it is selected EONTA LOCAL/EONTA DISTANCE mode. The purpose of this
key is to reduce unwanted EON TA switching, which EON TA information was received from current
station and the radio switched to that EON linked station, but no information could not be received
because the EON linked station is located too far from that area. So the radio is switched back to
current station again. In above operation, a customer listen to a wrong program or mute sound for a
while.
1) EONTA LOCAL mode:
When the filed strength level of EON linked is less than the threshold level, the radio does not switch
that station, and a customer can hardly listen to any disturbances.
When EONTA LOCAL mode is selected, EONTA LO on numeric display is indicated for a few seconds.
2) EONTA D ISTANCE mode:
EON TA switching is try to implemented by the information of current station. When EONTA
DISTANCE mode is selected, EONTA DX on numeric display is indicated for a few seconds.
14. PTY (PROGRAM TYPE) BUTTON
Press it briefly and repeatedly to select one of the following mode: POP M- - NEWS
While selecting PTY TYPE, its selection is implemented by preset buttons as described in preset key.
(press one of the 6 preset buttons shortly and repeatedly to select the PTY TYPE in the preset button)
When POP M or NEWS is on, the previous PTY program and PTY word is displayed on LCD. If there are no
keys
Entered for 2 seconds, previously selected PTY is searched. During 1 loop, if desired PTY is not found, NO
PTY is flashed, then return to previous normal radio and PTY icon goes off.
15. CLOCK BUTTON
Press the CLK button briefly to display time for 5 seconds on the display, and then returns to its previous
display unless the button is pressed again.
Then press the CLK button and hold for more than 1 seconds until the real time flashes on the display.
Then you can adjust HOUR or MINUTE by rotating the VOL knob.
16. SCAN BUTTON
Press the SCN button to scan the radio frequency. If a valid signal has detected, the current frequency will
be hold and blinking for 5 seconds, then press SCN again to stop scan and remain the current
frequency; otherwise, the radio will go on to scan the other radio frequency 5 seconds later.
17. AUX INPUT JACK
Press the mode button to select auxiliary input playing mode. Then you can connect any matched external
audio device to this socket. Use the volume knob to adjust volume.
18. EJECT KEY
In the power on state, the loaded disc can be ejected by pressing the EJ key.
19. CD SLOT
20. USB SOCKET
When needing to play the file in the USB stick, turn over the plastic cover cap then insert the USB stick
into the USB socket. The system will change into the USB mode automatically, and then play the first file
in the USB. When no needing to do USB operation, please cover the plastic cover cap.
21. SD CARD SLOT
When you need to play the file in the SD card, insert the SD card into the card
slot. The system will change into the SD mode automatically, and then play the first file in the SD.
Note: When SD card and USB stick are both inserted into their slot or socket, the system will change into
the USB mode automatically.
22. F L A S H I N G L E D
When the front control panel is removed this indicator flashes.
23. RESET BUTTON
Before operating the unit for the first time, or after replacing the car battery or changing the connections.
You must reset the unit.
Press this button with a cuspidal object. This operation will erase the clock setting and some stored
contents.