Depending on the required depth of cut, the fence (6) can also be
positioned between the strips (18).
• Mount the table clamps (7) (fig. F6) to the rear of the table supports (34)
(fig. F7).
• Place the fixed table section (4) on the table base as shown and check
that the holes in the middle locate over the adjustment screws in the
central table support (fig. F8).
• Use the M8 x 30 bolts and D8 flat washers at the top and D8 Belleville
washers at the bottom.
• Manually tighten all bolts in the fixed table section (4) except for the bolt
in the large central hole.
• Place the fence (6) and the strips (18) (fig. F6) on the table base (fig. F9).
• Tighten the table clamps.
• Firmly tighten all bolts in the table top.
Mounting the table extension (fig. F9 - F11)
• Mount the table extension supports (40) to the left-hand side of the
fixed table section (4) as shown using the M8 x 30 bolts at the top and
D8 Belleville washers at the bottom (fig. F10).
• Place the table extension (19) (fig. F6) on the protruding table extension
supports (fig. F11).
• Check that both tables are flush and tighten the bolts manually.
• Reposition the strips (18) and tighten the table clamps (7) (fig. F9).
Both tables must be flush at the rear.
The saw blade (fig. G1 - G5)
Mounting the saw blade (fig. F1)
The teeth of a new blade are very sharp and can be
dangerous.
The direction of rotation is indicated by the arrow on the motor.
• Hold the arbor using the Allen key supplied with the machine and remove
the arbor nut (41) by turning clockwise with the multifunctional spanner.
• Mount the blade (42) between the outer flange (43) and the inner flange
(44) making sure that the lower teeth point to the rear of the machine.
Make sure that the ring of the arbor nut (41) is against the
outer flange (fig. F1).
• Tighten the arbor nut (41) by turning counterclockwise.
Checking that the arm is parallel to the table top (fig. A1, F5 & G2)
• Tighten the riplock (15) with the blade in front position (fig. A1).
• Lower the blade until it only just touches the table top (4) (fig. G2).
• Release the levers (9) and (10) (fig. A1).
• Swing the arm so that the blade skims the table top across its width.
• If required, adjust the front adjusting bolt (38) (fig. F5).
• Repeat this procedure with the blade in rear position and adjust the
rear bolt if required.
Checking that the blade is perpendicular to the table top
(fig. A1 & G3 - G5)
• Bring the arm back to central position and tighten the riplock (15) (fig. A1).
• Place a steel square (45) against the blade body (fig. G3).
• If adjustment is required, proceed as follows:
• Remove the bevel pointer disk (46) by loosening the two screws (47)
(fig. G4).
• Loosen all three Allen screws that will be exposed in this way (fig. G5).
23
• Place an Allen key in the motor arbor and tap until the blade is flat
against the square.
• Firmly tighten all fasteners.
It is particularly important to tighten the central Allen screw.
• Replace the bevel pointer disk (46).
Checking that the crosscut travel is perpendicular to the fence
(fig. G6 - G10)
• Lock the blade in front of the fence (fig. G6).
• Place a square (45) on a piece of board and against the fence and just
touching the blade as shown.
• Unlock the riplock, pull the blade towards you to check that the blade
traverses parallel to the square.
• If adjustment is required, proceed as follows:
• With the mitre latch lever (9) engaged in 0° position, release the mitre
clamp lever (10) (fig. G7).
• Loosen the locknuts (48) on each side of the arm (fig. G7 & G8).
• To adjust the arm to the left, loosen the stud (49) on the righthand side
of the arm and tighten the opposite stud (fig. G9).
• To adjust the arm to the right, loosen the stud (50) on the lefthand side
of the arm and tighten the opposite stud.
• Proceed in small steps and check the adjustment after each step with
the levers (9) and (10) engaged.
Do not overtighten the studs.
• Tighten the locknuts (48) (fig. G7 & G8).
• Adjust the pointer (51) on the mitre scale (52) so that it registers 0°
(fig. G10).
Checking that the blade is perpendicular to the fence (fig. G11 - G13)
• Unlock the yoke clamp lever (53) press the yoke latch (54) (fig. G11).
• Rotate the motor through 90° as shown.
• If the motor shows a certain play, tighten the nut (55) (fig. G12).
• Place the blade against the fence and check that it is parallel to the fence.
• If adjustment is required, proceed as follows:
• Loosen the two bolts (56) installed crosswise under the yoke (fig. G13).
• Insert the Allen key into the motor arbor.
• Adjust the blade position and tighten the bolts (56).
Mounting and adjusting the blade guard assembly (fig. H1 - H5)
The blade guard (3) is a multifunctional assembly which offers the following
safety features (fig. H1):
- Front guard (57) (fig. H1) and spring held rear guard (58) (fig. H2) for full
blade protection.
- Dust extraction adapter (59) for cross and rip cutting.
- Anti-kickback fingers (60) for use in ripping mode.
- Adjustable finger guard (61) for use when cross-cutting.
- Riving knife (62) to prevent the workpiece binding on the blade when
ripping.
• Release the bevel clamp lever (36) and pull out the bevel latch (37)
(fig. F2) to tilt the motor as shown for optimum access (fig. H3).
• Remove the guard retaining wing nut (63) and washer (64).
• Loosen the locking screw (65) and turn the retaining bracket (66)
counter-clockwise until the spring held rear guard (58) can be lifted off
its support lug (68) (fig. H3).
• Unhook the two springs (67) at the top only.
• Rotate the unhooked rear blade guard (58) as shown in figure H2.
• Lower the guard assembly over the blade (fig. H3).
E N G L I S H
en - 5