Nibe RG 10 Montageanweisung Seite 4

GB
Connecting
Positions on RG 10:
F :
6 Signalground
G :
1 Setting (set point value)
H :
2 Room temp (actual value)
RG 10 is connected as follows. (See corresponding
Installation and Maintenance Instructions for terminal
block positions.)
FIGHTER 310P/410P
F -> Terminal block 14, 4
G -> Terminal block 14, 5 Channel 15
H -> Terminal block 14, 6 Channel 16
FIGHTER 360P
F -> Terminal block 14, 13
G -> Terminal block 14, 16
H -> Terminal block 14, 12
EVC 240, EVP 270
F -> Terminal block 14, –
G -> Terminal block 14, Set
H -> Terminal block 14, Actual
EVC 13
F -> Terminal block 14, 4
G -> Terminal block 14, 5
H -> Terminal block 14, 6
FIGHTER 1140/1150/1240/1250
F -> Terminal block X1, 4*
G -> Terminal block X1, 14*
H -> Terminal block X1, 3*
FIGHTER 1330
F -> Terminal block X1, 13*
G -> Terminal block X1, 14*
H -> Terminal block X1, 12*
ACVM 270
F -> Terminal block X4, 2*
G -> Terminal block X4, 1*
H -> Terminal block X4, 3*
* Terminal block X1/X4 is located on the EBV-card (2/AA22) in
FIGHTER 1140/1150/1240/1250/1330/ACVM 270.
** Applies only to FIGHTER 360P/1135/1150/1235/1250/1330/
ACVM 270.
4
6 1 2
F G H
Rumsgivare, RG 10
6 1 2
F G H
14
Externt telefonmodem
erhålls ej av Nibe
potentialfri
kontakt
A B I II III A B I II A B I II
-2 0
+2
14
14
Terminal block 14
is located behind
60
40 °C 80
20 100
the left cover in
0 120
2
1 bar 3
0 4
the elec trical
con nec tion area.
X1
X4
NIBE RG 10
Adjustment during installation
The room sensor is primarily intended to correct decreases
in room temperature due to causes other than changes
in the outdoor temperature, for example, centralised load
control.
The room sensor corrects the curve slope so that the flow
temperature changes. If the room temperature changes
the room sensor senses this and lets the processor change
the flow temperature.
Any radiator valves ought to be fully open in areas where
the room sensor is installed.
Activation**
RG10 must be activated in the menu.
FIGHTER 360P: Menu 9.1.14
FIGHTER 1135/1150/1235/1250: Menu 9.2.18
FIGHTER 1330: Menu 9.1.11
ACVM 270: Menu 9.3.6
Note!
Work behind screwed covers may only
be carried out under the supervision of a
qualified installation engineer.
External control of the room tempe-
rature, extra option (does not apply
to F360P/1140/1150/1240/ 1250)
The room temperature can be altered between two pre-
set values. If the room sensor connection is supplemen-
ted with an external potential free contact function, for
example telephone switch or clock, the preset values can
be used. When the contact function is made the room
sensor is connected and influences the flow temperature.
Example: The basic setting gives a specific flow tempera-
ture. The room sensor is set to a lower temperature. When
the contact is made, the lower temperature applies until
the contact will be broken again.
6 1
F G
Room sensor RG 10
Rumsgivare, RG 10
6 1
F G
Connection to be done on terminal block 14/X1/X4 in all before mentioned heat
pumps and electric boilers. Note that connection to ACVM 270 must be carried out
according to section "Connecting external contacts" in the product's Installation
and Maintenance instructions.
2
H
2
H
External modem
Externt telefonmodem
(not supplied by NIBE)
erhålls ej av Nibe
Potential free
potentialfri
kontakt
contact