Operation; Preparing The Icemaker For Long Storage; Maintenance - Hoshizaki KM-40B Bedienungsanleitung

2. All parts are factory-adjusted. Improper adjustments may result
in failure.
3. If the unit is turned off, wait for at least 3 minutes before
restarting the icemaker to prevent damage to the compressor.

1. OPERATION

The installer will normally commission the icemaker to start the automatic
icemaking process. To ensure continuous operation, make sure that:
* The water supply tap is on,
* The icemaker is plugged into the power supply, and
* The control switch is in the "ICE" position (remove the air filter to
check).

2. PREPARING THE ICEMAKER FOR LONG STORAGE

1) Move the control switch to the "OFF" position.
2) Unplug the icemaker or disconnect the power supply.
3) Close the water supply tap, and remove the inlet hose.
4) Remove all ice from the storage bin, and clean the bin.
5) Disconnect the silicone hose to drain the water from the water tank.
Reconnect the silicone hose back in its correct position after all of
the water has drained. See Fig. 5.
Cube Guide
Water Tank
Silicone Hose
(Connect/disconnect
arrowed part)
Storage Bin
III. MAINTENANCE
1. CLEANING
WARNING
1. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to check and clean the condenser
at least once a year.
3. This appliance must not be cleaned by use of a water jet.
4. Do not use any alcohol for cleaning/sanitisation of the icemaker.
It may cause cracks on the plastic parts.
5. Do not remove the top panel and louver. Only a qualified service
person should remove them.
6. To prevent possible damage, do not clean the plastic parts
with water above 40°C or in a dishwasher.
Overflow Pipe
Fig. 5
[1] Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use a
damp cloth containing a neutral cleaner to wipe off grease or dirt.
[2] Scoop and Bin Door Grip Cleaning/Sanitisation (Daily)
1) Either mix 3 litres of water with 11 ml of 5.25% sodium hypochlorite
solution in a suitable container, or the recommended Hoshizaki
sanitiser as directed.
2) Soak the scoop in the solution for more than 3 minutes. Rinse
thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
3) Use a neutral cleaner to wash the bin door grip. Rinse thoroughly.
4) Soak a clean cloth with the sanitising solution, and wipe the grip. Use
fresh water and a clean cloth to rinse/dry.
[3] Storage Bin Interior Cleaning/Sanitisation (Weekly)
1) Open the storage bin door, and remove all ice.
2) Wash the bin liner with a neutral non-abrasive cleaner. Rinse
thoroughly.
3) Soak a clean cloth with the neutral cleaner, and wipe the door inner
surface. Wipe off the cleaner with a clean damp cloth.
4) Either mix 3 litres of water with 11 ml of 5.25% sodium hypochlorite
solution in a suitable container or the recommended Hoshizaki
sanitiser as directed.
5) Soak a clean sponge or cloth with the solution, and wipe the bin liner
and bin door.
6) Rinse thoroughly with fresh water and a clean cloth to wipe off the
solution. Close the bin door.
Note: Some solutions may cause damage to the bin liner surfaces or
corrosion on the metal parts. Always rinse the sanitiser unless
directed otherwise by Hoshizaki guidelines.
[4] Air Filter
Plastic mesh air filters remove dirt or dust from the air, and keep the
condenser from getting clogged. If the filters get clogged, the icemaker's
performance will be reduced. Remove and clean the air filters at least
twice per month:
1) Remove the air filter.
Note: Do not put your hand inside the machine compartment.
2) Clean the air filter by using a vacuum cleaner. When severely clogged,
use warm water and a neutral cleaner to wash the air filter.
3) Rinse and dry the air filter thoroughly, and place it in position.
[5] Icemaking Water System
To keep the icemaker hygienic, periodic cleaning of the icemaking water
system is recommended. Always ask a trained service person to clean
the water system.
Note: The user is allowed to move the control switch to the "ICE" or
"OFF" position. Only a qualified service person should move it to
the "WASH" position to flush the icemaking water system.
5
ENGLISH